Kenmore 970 Use & Care Manual page 13

6, TO remove Freezer Door _.o_k.,_.,Jte ova,
freezer handle: Dowtai_ Button
Reverse handles
while doors are
off° Remove the Dov_t_t
two screws _ut_o.
attaching the
handle to the
bottom of the
freezer door.
Swing bottom of
handle away from Plug
the door and slide
handle up and off
dovetail button.
Remove screw
and dovetail button and install on other side, moving hole
plug from corresponding hole to the opposite side,, Reverse
instructions for reattaching handle, Start with handle offset
away from the door, Place top of handte over dovetail
button, swing handle into an upright position and push
upward, locking it into place. Secure bottom of handle with
screws,
7. To remove
refrigerator
handle: Pull
down to slide
trim off bottom of
handle,, Remove
the two screws
attaching the
handle to the top
of the refrigerator
door. Swing the
top of handle
away from the
door and slide
handle down and
off dovetail
button. Remove
screw and
dovetail button
and install on
other side,
moving hole
plugs from
Refrigerator Door
S(:r_w$
.......... !,. /
Lock Nandie Over
Dover°i| Button
/ =!:4_
corresponding
T_im Lock Adhesive
holes to the trim_.°_:k
opposite side, Reverse instructions for reattaching handle.
Start with the handle offset away from the door. Place
bottom of handle over dovetail button, swing handle into
an upright position and push downward, locldng it into
place Secure top of handle with screws. Replace trim.
THIn Removal (Full-Length Trim models only):
In some models, the refrigerator door has a full length
trim piece which continues from the bottom of the handle
to the bottom of the door. The top of the trim fits around
the base of the handle, An adhesive "trim lock" is
positioned about haff-way down. The bottom of the trim is
held in place by either an adhesive trim lock, or a trim lock
with two prongs inserted into a hole on the face of the
door Remove the trim by gently pulling the trim lock areas
out and away from the door When the trim is free from the
door, gently putt the trim down and away from the base of
the handle, using a slight side to side motion.
To reattach trim; Slide both trim locks out of trim,, Insert
the new adhesive trim locks contained in your literature
pack, NOTE: Trim lock must be removed and installed by
sliding OVER the two donut shaped areas. Install trim to
handle by sliding over base of handle, Carefully align trim
and press down at trim lock locations. Replace hole plug
on opposite side, Use rubbing alcohol to remove any
adhesive residue from old trim lock location(s),,
8. Remove door
stop from bottom
of freezer and
refrigeratordoor
and reinstall on
opposite side.
Freezer Door
l" 4_ Door Stop
_._-- Screw
Refrigerator Door
9. if your
refrigerator does
not have a Toe
Grille, use a putty
knife to remove the
plastic plug (not
shown) from front
of base and
reinstall in the
opposite set of
lower hinge holes.
Assemble lower
hinge to cabinet,
Install hinge pin in
opposite hinge hole
from which it was
removed Install
the washer (some
models) on the
lower hinge pin and
insert hinge
screws, but do not
Hinge Pin
Lo!er Hinge
Or
Washer
Pin
Screws
Lower ge
tighten. Hinges will have to remain loose against cabinet to
align door.
t0. Turn center
hinge upside down
and secure to
cabinet as shown,
using the screws
which are in the
new holes. Install
refrigerator door on
lower hinge pin,
Align door with
edge of cabinet.
Hold the door on
front of cabineL
[enter Hinge
(upsSde down)
13