Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Tool Shed TSCCS
Summary of Contents for Tool Shed TSCCS
- Page 1 CONCRETE CUTTING TSCCS www.thetoolshed.co.nz...
-
Page 2: Table Of Contents
OPERATION MANUAL OPERATION MANUAL TABLE OF CONTENTS PRODUCT DETAILS Product Details Product Model ToolShed Concrete Cutting Saw Specifications Product Identification Product Code TSCCS Safety Guidelines Assembly Fuel Handling Operation Starting & Stopping Maintenance DISTRIBUTED BY: Storage Troubleshooting Thank You Note: For the purchase of this ToolShed product. -
Page 3: Specifications
OPERATION MANUAL OPERATION MANUAL SPECIFICATIONS PRODUCT IDENTIFICATION Cylinder Displacement 74 cc/rev Cylinder Bore 51 mm Stroke 36 mm Idle Speed 3000 RPM Wide Open Throttle Load 9300 RPM Power 3.5 kW @ 9000 RPM Fuel Tank Capacity 1 Litre Recommended Water Pressure 0.5–10 Bar | 7–150 PSI Net Weight (Without Fuel &... -
Page 4: Safety Guidelines
OPERATION MANUAL OPERATION MANUAL SAFETY GUIDELINES SAFETY GUIDELINES Power Tool & Machinery Use & anything else that could be of risk, away from WARNING Care moving parts in the machine, or they could be caught therein. • Use the correct tool for the job. Forcing READ ALL SAFETY WARNINGS &... - Page 5 OPERATION MANUAL OPERATION MANUAL SAFETY GUIDELINES SAFETY GUIDELINES Fuel & Engine Safety Gasoline & Vapours When Adding or Removing When Starting the Engine Gasoline • • Engine exhaust contains carbon monoxide, a DO NOT attempt to start a damaged engine. •...
- Page 6 OPERATION MANUAL OPERATION MANUAL SAFETY GUIDELINES SAFETY GUIDELINES • • Service Stop Switch The throttle lock remains pressed in as long Check that the cutting blade is fitted correctly as the throttle is pressed. When the grip on and does not show signs of damage. A •...
- Page 7 OPERATION MANUAL OPERATION MANUAL SAFETY GUIDELINES SAFETY GUIDELINES Muffler Abrasive Blades Diamond Blades WARNING • The muffler is designed WARNING WARNING to keep noise levels to a NEVER use a cutting blade for any other minimum and to direct material than it was intended to cut. Do not use the abrasive blades with Diamond Blades become very hot exhaust fumes away from...
-
Page 8: Assembly
OPERATION MANUAL OPERATION MANUAL ASSEMBLY ASSEMBLY • • Checking the Arbour Bushing Fitting the Blade The blades for this machine are high speed Press the ends of the guard against the work blades approved for hand held power cutters. piece or adjust the guard with the adjustment •... -
Page 9: Fuel Handling
OPERATION MANUAL OPERATION MANUAL ASSEMBLY FUEL HANDLING • Reversible Cutting Head Mixing Disconnect the water hose nipples and handle NOTICE from the blade guard (C). Remove the stop (D). • • The machine is fitted with a reversible cutting Always mix the petrol and oil in a clean head, allowing cutting close to a wall, or at container intended for fuel. -
Page 10: Operation
OPERATION MANUAL OPERATION MANUAL OPERATION OPERATION • • General Safety Other PPE Gear Never cut asbestos materials! The guard for the cutting equipment should • Hold the saw with both hands; keep a firm be adjusted so that the rear section is flush •... - Page 11 OPERATION MANUAL OPERATION MANUAL OPERATION OPERATION • Managing Dust Reactive Force Climbing Kickback Stand at a comfortable distance from the work piece. • • • This machine is fitted with a low flushing water A reactive force is always present when If the kickback zone is used for cutting, the •...
-
Page 12: Starting & Stopping
OPERATION MANUAL OPERATION MANUAL OPERATION STARTING & STOPPING • Pipe Cutting Proper sequence for cutting a pipe: With a Cold Engine • 1. First cut section ‘I’. • • Special care should be taken when cutting into Ensure that the stop switch (STOP) is in the left •... -
Page 13: Maintenance
OPERATION MANUAL OPERATION MANUAL STARTING & STOPPING MAINTENANCE • Spark Plug • Before cleaning or performing any mainte- Grip the front handle with your left NOTICE nance, you must ensure the tool is switched hand. Put your right foot on the •... - Page 14 OPERATION MANUAL OPERATION MANUAL MAINTENANCE MAINTENANCE • • • Starter Housing Wiggle the blade guard (E) up and down 3-5 Replace the drive belt. Turn the belt tensioner The carburettor is equipped with fixed times, and then tighten the nuts (A) with the (B) to position “1”...
-
Page 15: Storage
OPERATION MANUAL OPERATION MANUAL MAINTENANCE STORAGE Fuel System Replacing the Air Filter Transport & Storage with Blades Long-Term Storage • • • • Check that the fuel cap and its seal are not Loosen the screws. Do not store or transport the power cutter When storing the machine for long periods, •... -
Page 16: Troubleshooting
OPERATION MANUAL TROUBLESHOOTING FAULT POSSIBLE CAUSE SUGGESTED SOLUTION See instructions under ‘Starting & Incorrect starting procedure Stopping’. Stop switch in the right (STOP) Ensure the stop switch (STOP) is in position the left position. The Machine Does Not There is no fuel in the fuel tank Refill with fuel.
Need help?
Do you have a question about the TSCCS and is the answer not in the manual?
Questions and answers