1. Manuals
  2. Brands
  3. ABL Manuals
  4. Automobile Battery Charger
  5. POLEMH1
  6. Installation manual

ABL POLEMH1 Installation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
POLEMH1
POLEMH2
EN
POLEMH3
Installation manual
Article No.: 0301691_EN_b

Advertisement

Table of Contents
loading

Related Manuals for ABL POLEMH1

Summary of Contents for ABL POLEMH1

  • Page 1 POLEMH1 POLEMH2 POLEMH3 Installation manual Article No.: 0301691_EN_b...
  • Page 2 Contact Contact ABL GmbH Albert-Büttner-Straße 11 91207 Lauf an der Pegnitz Germany +49 (0) 9123 188-0 +49 (0) 9123 188-188 info@abl.de www.ablmobility.de Customer Service +49 (0) 9123 188-0 service@abl.de www.ablmobility.de/en/service/support/ NOTE Please note that the wallboxes shown on the cover sheet are not included with the respective POLEMHx, but can be ordered separately for a fee.

  • Page 3: Table Of Contents

    Positioning the EMH9999 foundation and installing the POLEMHx Specifications for the mechanical and electrical installation of the wallboxes Installing the eMH1 Wallbox on the POLEMH1 Installing the eMH2 Wallbox on the POLEMH2 Installing the eMH3 Wallbox on the POLEMH6 Electrical connection in the POLEMHx...

  • Page 4: Additional Technical Information

    POLEMHx can be installed on the optionally available EMH9999 concrete foun- dation or on a self-constructed concrete foundation. To protect the installed wallbox from the weather, ABL offers the compatible WPR12 (POLEMH1/2) and WPR36 (POLEMH3) weather shield. For cable management at the charging point, the CABHOLD cable holder with charging plug receptacle can retrofitted.

  • Page 5: Important Information General

    ƒ Please read this manual carefully. ƒ Heed all warnings and follow all instructions. ƒ Only use accessories intended and sold for the product by ABL. ƒ Do not install this device in close vicinity to running water, water jets or areas subject to flooding.

  • Page 6: User Information

    Important information – User information ƒ Electrical installation and testing must be carried out with reference to local rules by a qualified specialist electrical contractor, who, on the basis of their specialist training and experience, as well as their knowledge of the relevant standards, is able to assess and carry out the working steps described in this manual and recognise potential hazards.
  • Page 7 Important information – User information ƒ No user-maintainable parts are located inside the device. ƒ Only have the POLEMHx repaired by a qualified specialist electrical company. ƒ The wallbox installed on the POLEMHx may only be operated after it has been installed without any technical faults and subsequently approved by a qualified specialist electrical company.

  • Page 8: Dimensional Drawings And Dimensions

    POLEMH1 (see “Accessories” on page 13). These six thread points are used for directly mounting a WHEMH10 or 1W0001 mounting plate on the POLEMH1 (see “Accessories” on page 13). The eMH1 Wallbox is then screwed to the mounting plate.

  • Page 9: Polemh2

    Dimensional drawings and dimensions – POLEMH2 POLEMH2 Mounting pole for installing an eMH2 Wallbox, front, side and rear view as well as view from below (all dimensions in mm) Front 60 90 Detailed view of the front These four thread points are used for directly mounting the eMH2 Wallbox on the POLEMH2.

  • Page 10: Polemh3

    Dimensional drawings and dimensions – POLEMH3 POLEMH3 Mounting pole for installing an eMH3 Wallbox, front, side and rear view as well as view from below (all dimensions in mm) Front 60 90 Detailed view of the front These four thread points are used for directly mounting the eMH3 Wallbox on the POLEMH3.

  • Page 11: Emh9999

    Dimensional drawings and dimensions – EMH9999 EMH9999 ABL offers the EMH9999 foundation as an optional accessory for installing the POLEMHx: The foundation block is made from grade C30/37 concrete and complies with exposure classes XC4 and XF1 for outdoor use. Integrated threaded anchors ensure stable and secure installation of the POLEMHx, and the supply line and data cables can be fed into the mounting pole from below via recessed pipelines.

  • Page 12: Introduction To The Polemhx

    Thank you very much for choosing the POLEMHx mounting pole from ABL! The POLEMHx is designed for the outdoor installation of an ABL Wallbox. With its internal terminal block, the PO- LEMHx makes it particularly quick and easy to connect the wallbox to the local power grid. Access is via a rear hous- ing door, which is protected against unauthorised access by integrated locks.

  • Page 13: Accessories

    ƒ CABHOLD Cable holder with charging plug receptacle for installation on an exterior wall or the mounting poles POLEMH1/2/3 h = 187 mm, w = 76 mm, d = 105 mm You can find further information on ABL charging stations and accessories at www.ablmobility.de.

  • Page 14: Installation

    POLEMHx directly on asphalt or a concrete floor, but to use a concrete foundation such as the ABL EMH9999 with suitable specifications (concrete C20/25 in accordance with EN 206-1:2013). ƒ A sufficiently dimensioned supply cable for the power supply of the respective wallbox must be provided at the installation location.

  • Page 15: Positioning The Emh9999 Foundation And Installing The Polemhx

    ƒ Concrete screed (mixed) Positioning the EMH9999 foundation and installing the POLEMHx The optional EMH9999 concrete foundation from ABL provides a level installation surface for all POLEMHx mounting poles and ensures the necessary stability and support via factory-inserted screw anchors.
  • Page 16 Installation – Positioning the EMH9999 foundation and installing the POLEMHx Apply a first layer of concrete screed with a height of approx. 10 cm at the positioning location of the foundation. Place the foundation centrally on the concrete screed. Make sure the supply cable can be insert- ed into the pipe opening on the foundation in this position.
  • Page 17 Installation – Positioning the EMH9999 foundation and installing the POLEMHx Fill the entire ditch around the foundation to ground level with compactable soil. y The soil must be filled and compacted in layers and evenly on all sides. Smooth out the surface. Use the triangular key supplied to open the housing door of the POLEMHx and flip it open.

  • Page 18: Specifications For The Mechanical And Electrical Installation Of The Wallboxes

    The EMH9999 foundation has eight recessed threaded anchors for screwing on the POLEMHx (see illustration in section “EMH9999” on page 11). ƒ To secure the POLEMH1 and POLEMH2, use the four inner threaded anchors. ƒ To secure the POLEMH3, use the four outer threaded anchors.

  • Page 19: Installing The Emh1 Wallbox On The Polemh1

    Installing the eMH1 Wallbox on the POLEMH1 This section describes how to install the eMH1 Wallbox on the POLEMH1. If using an optional WHEMH10 or 1W0001 mounting plate, please refer to the instructions for mounting plates.
  • Page 20 Installation – Installing the eMH1 Wallbox on the POLEMH1 Remove the upper part of the housing from the housing base. Connect a supply cable measuring approximately 1.5 metres in length to the internal RCCB or termi- nal block (basic models) of the eMH1.
  • Page 21 Installation – Installing the eMH1 Wallbox on the POLEMH1 Insert the supply cable through the right-hand grom- met into the housing of the POLEMH1 and hang the wallbox on the screw in the upper fixing point. Using the hexagon screwdriver and the two M6×16 screws supplied, screw the wallbox into the two lower fixing points.

  • Page 22: Installing The Emh2 Wallbox On The Polemh2

    Installation – Installing the eMH2 Wallbox on the POLEMH2 Switch to the rear of the opened mounting pole and pull the supply cable of the wallbox to the terminal block of the upper top-hat rail. This completes the installation of the wallbox on the mounting pole. Go to the section “Electrical connection in the POLEMHx”...
  • Page 23 Installation – Installing the eMH2 Wallbox on the POLEMH2 Connect a supply cable measuring approximate- ly 1.5 metres in length to the internal RCCB of the eMH2. y To establish the connection, the grommet of the wallbox must be cut and the supply cable insert- 1,5 m ed into the interior of the housing.
  • Page 24 Installation – Installing the eMH2 Wallbox on the POLEMH2 Insert the supply cable through the large grommet into the housing of the mounting pole and hang the wallbox on the two screws on the mounting pole. Use the two supplied M6×16 cylinder-head screws and the hexagon screwdriver to screw the wallbox into the two lower fixing points.

  • Page 25: Installing The Emh3 Wallbox On The Polemh6

    Installation – Installing the eMH3 Wallbox on the POLEMH6 NOTE Dehumidifying the POLEMH2 To dehumidify the interior, we recommend filling the base area of the POLEMH2 with dry granulate. This minimis- es any unwanted effects due to condensation and seepage water penetration. Installing the eMH3 Wallbox on the POLEMH6 This section describes how to install the eMH3 Wallbox on the POLEMH3.
  • Page 26 Installation – Installing the eMH3 Wallbox on the POLEMH6 Loosen the screw holding the internal electronic components cover in place using a Torx screwdriver and put it aside. y Keep the screw in a safe place. Insert the power supply cable into the housing through the large grommet.
  • Page 27 Installation – Installing the eMH3 Wallbox on the POLEMH6 Insert the supply cable through the large grom- met into the housing of the mounting pole and screw the wallbox into the mounting plate using the screwdriver and the screws supplied with the wallbox.

  • Page 28: Electrical Connection In The Polemhx

    Installation – Electrical connection in the POLEMHx Switch to the rear of the opened mounting pole and pull the supply cable of the wallbox to the terminal block of the upper top-hat rail. This completes the installation of the wallbox on the mounting pole. Go to the next section “Electrical connection in the POLEMHx”.
  • Page 29 Installation – Electrical connection in the POLEMHx NOTE Strain relief of the supply cable It is advisable for the power supply cable be attached to the lower C-rail of the POLEMHx via a suitable strain relief. Wallbox Insert the individual conductors of the two cables into the respective terminals and tighten them us- ing the Phillips-head screwdriver.

  • Page 30: Safety Instructions For Start-Up And Operation

    Installation – Safety instructions for start-up and operation Connect the supply cable to the mains. y As soon as the wallbox is connected to the elec- tricity grid, it will initiate the start-up procedure. Measure the voltage at the individual terminals us- ing the voltage tester.

  • Page 31: Troubleshooting And Maintenance

    Troubleshooting and maintenance – Maintenance Troubleshooting and maintenance If a malfunction should occur during operation, first check the points mentioned below. If the error cannot be recti- fied, contact your local sales partner and jointly determine how to proceed. The following malfunctions may occur: Malfunction Possible cause and suggested solution The power cable to the wallbox and/or the supply cable has not been correctly con-...

  • Page 32: Appendix

    Appendix – Technical specifications Appendix Technical specifications Model code POLEMH1 POLEMH2 POLEMH3 Compatibility (wallbox) eMH1 eMH2 eMH3 External power supply for supply cable sizes up to 5 x 6 mm² Rated voltage (power supply) 230/400 V Rated current (power supply) up to 32 A, 3-phase Rated frequency 50 Hz...

  • Page 33: Trademarks

    Appendix – Trademarks Trademarks All trademarks mentioned in this manual, including those that may be protected by third parties are, without restric- tion, subject to the regulations of the respectively applicable trademark law and the property rights of the respective registered owners.
  • Page 34 ABL GmbH Albert-Büttner-Straße 11 91207 Lauf an der Pegnitz Germany +49 (0) 9123 188-0 +49 (0) 9123 188-188 info@abl.de www.ablmobility.de...

This manual is also suitable for:

Polemh2Polemh3

Table of Contents