ABH 6400 Series Manual

6400 SERIES PRIVACY LATCH THUMBTURN LOCK -
NOTES
1. TRIM CAN ONLY BE MOUNTED DOWN, VERTICALLY WITH HANDLE DOWN.
2. USES STANDARD 161 DOOR PREP.
3. VISION LITE MUST BE AT LEAST 6" FROM CENTERLINE OF TRIM.
8
(PUSH SIDE)
PRIVACY
CAM PINS
PRIVACY
CAM SHAFT
DETAIL "B"
CAM
PIN
PUSH SIDE
PULL SIDE
INSTALLATION INSTRUCTIONS:
1. Prep door according to latch backset per template.
2. Install latch (item 1) using either wood or machine screws (items 2 or 3) depending on door type.
3. Take both base assemblies (item 4 & 6) and rotate cam pin as shown in Detail "A" above. Place pull base locking assembly
(item 4) on pull side of door and slide the cam shaft though the latch cam. Place push base override assembly (item 6) on push
side of door and engage push cam onto the pull side cam shaft. Both privacy cam pins must be at the 12 o'clock position in
order for the privacy cam shafts to interlock as shown in Detail "B'. Check that they are interlocked properly by rotating one
privacy cam and making sure the other side is rotating at the same time.
4. Fasten both sides using (4) 12-24 machine screws and lock nuts (item 5 & 7). Test both handles for free movement of the latch bolt
before tightening all screws. If latch bolt does not extend or retract freely because of any type of binding, loosen screws to align
adjustment of base assemblies and retighten screws one at a time while checking for proper latch retraction. Mounting hardware
(items 5 & 7) must be tightened before proceeding to next step.
5. Place override cover assembly (item 8) on the push side of the door making sure that the forks on the inside of the cover engages
the privacy cam and fasten with (2) 8-32 screws (item 2).
6. Repeat Step 5 with locking cover (item 9) on the pull side of the door.
PATENT No. 6,196,599 & 6,293,598
FORK
2
PRIVACY
CAM PIN
7
1
2
3
LATCH CAM
ALL PREP MOUNTING HOLES
TO BE STRAIGHT & PARALLEL
TO ONE ANOTHER, THIS WILL
HELP PREVENT ANY BINDING
OF MECHANICAL PARTS.
DETAIL "A"
BEFORE MOUNTING BASE ASSEMBLIES
CAM
CAM PIN MUST BE ROTATED TOWARDS
PIN
SIDE INDICATED BY BY DETAIL.
PULL SIDE
**
6
PRIVACY
CAM SHAFT
VERIFY CORRECT BACKSET AND HORIZONTAL
OR VERTICAL MOUNTING BEFORE DRILLING.
THEN USE BACKSET TEMPLATE THAT IS SUPPLIED.
PRIVACY
CAM SHAFT
CAM
SHAFT
QTY
ITEM PART DESCRIPTION
1
1 LATCH
2 6 8-32 X 3/8" FHMS
3 2 #8 X 3/4" FHWS
4
1 PULL BASE LOCKING ASSEMBLY
5 4 12-24 X 2-3/8" TRUSS HD. M.S.
6
1 PUSH BASE OVER-RIDE ASSY
7 4
12-24 LOCKNUT
8
1 PUSH COVER ASSEMBLY (OVER RIDE)
9
1 PULL COVER ASSEMBLY (LOCKING)
4
PRIVACY
CAM PIN
5
9
* *
HANDLES
DOWN
c 2 0 2 2 A B H M f g . , I n c .
REVISED 03-02-22
U
C US
L
R
LISTED
2
LOCKING
THUMBTURN
(PULL SIDE)
6400-1-16.DWG
6400
PAGE 1 OF 3