ABH 6600EO Series Installation

HANDLE INSTALLATION FOR MORTISE LOCK
NOTES
1. TRIM CAN BE MOUNTED UP, DOWN, HORIZONTALLY OR VERTICALLY.
2. VISION LITE MUST BE AT LEAST 6" FROM CENTERLINE OF TRIM.
3. USES 6600EO SERIES MORTISE LOCK DOOR PREP.
4. 6600EO MORTISE LOCK CYLINDER & LOCK CAM NOT PROVIDED.
SQUARE
-OR-
ROUND
COVER
PUSH SIDE
SHOWN
EXAMPLE
EDGE GUARD NOTE:
WHEN PREPPING THE DOOR,
DETERMINE IF THE DOOR WILL
RECEIVE AN EDGE GUARD, IF SO,
THE EDGE GUARD SHOULD BE
INSTALLED FIRST AND THEN THE
PREP FOR THE MORTISE LOCK
SHOULD BE MEASURED FROM THE
OUTSIDE EDGE OF THE EDGE
GUARD.
NOTE:
BEFORE MOUNTING BASE ASSEMBLIES
CAM PIN MUST BE ROTATED TOWARDS
SIDE INDICATED BY ARROW STAMPED
ON THE BASE.
DETAIL "A"
INSTALLATION INSTRUCTIONS:
1. Install mortise lock (item 10) using (2) 12-24 screws (item 12). Then mount the trim plate (item 11) using (2) 8-32 screws (item 13).
2. Before mounting adapter plate (item 6) & exit only plate (item 8), determine which side of the door will receive the push or pull handle
assembly (item 4) and the direction the handle will mount. Handle can be mounted up, down or horizontally.
3. Mount adapter plate (item 6) & exit only plate (item 8) to door with (2) 10-32 screws (item 5) thru door and mortise lock to (2) 10-32 sex
bolts (item 7). tighten securely.
4. Before mounting handle assembly (item 4), cam pin must be rotated towards the correct side of the handle (see detail A).
5. Mount handle assembly (item 4) to adapter plate (item 6) with (4) 10-32 screws (item 3) with (4) star washers (item 9).
6. Test lock for proper operation. If latch bolt does not extend or retract freely because of any type of binding, loosen mounting screws to
adjust alignment of trim handle assembly (item 4) and re-tighten screws one at a time while checking latch bolt movement.
7. Place cover (item 1) over handle assembly (item 4) and secure with (2) 8-32 screws (item 2) on each side.
8. If provided, install locking thumb turn (item 14) using (2) #8 screws (item 15).
PATENT No. 6,196,599 & 5,730,478
6600EO SERIES EXIT ONLY PUSH/PULL
1
2
3
9
4
CAM SHAFT
FOR
12
11
13
**
PUSH SIDE
OR
PULL SIDE
5
15
14
6
10
QTY
ITEM PART DESCRIPTION
1 1
COVER
2
2 8-32 x 3/8" FHMS
3 4 10-32 x 1/4" PAN HD. M.S.
4 1
PUSH OR PULL HANDLE ASSY
5
2 10-32 x 1-3/4" FHMS
6 1
ADAPTER PLATE
7
2 12-24 x 1/2" SEX BOLT
8
1
EXIT ONLY PLATE
9 4
#10 STAR WASHER
10 1
MORTISE LOCK
11
1
TRIM PLATE
12 2
12-24 x 3/4" FH COMBO
13 2
8-32 x 1/4" FHMS
14
1
LOCKING THUMB TURN (If used)
15 2
#8 x 1/2" FHSMS
7
8
* *
HANDLE HANDLE
UP DOWN
6600EO
PAGE 1 OF 3
c
ISSUED 03-28-19
U
C US
L
R
LISTED
HANDLE
HORIZONTAL
(MUST POINT
HINGE SIDE)
6600EO-1-03.DWG