ABH LR6000 Installation Instructions

10
11
8
9
2
EDGE GUARD NOTE:
WHEN PREPPING THE DOOR FOR
THE BACKSET, DETERMINE IF THE
DOOR WILL RECEIVE AN EDGE
GUARD, IF SO, THE EDGE GUARD
SHOULD BE INSTALLED FIRST AND
THEN THE PREP FOR THE LATCH
BACKSET SHOULD BE MEASURED
FROM THE OUTSIDE EDGE OF THE
EDGE GUARD.
DETAIL "A"
INSTALLATION INSTRUCTIONS:
1. Prep door according to LR6000 Series latch template
2. Install latch using either #8 wood screws or 8-32 machine screws (Item 2).
3. Check (1) base assembly (Item 3) to ensure the cam is the position shown in Detail A (See above)
Place the base assembly on the push side of the door by inserting the cam shaft into the latch cam as
detailed above.
4. Check the other base assembly (Item 3) and ensure the cam is the position shown in Detail A
(See above). Place base assembly on the pull side of door by engaging the shaft into the latch cam as
detailed above. Fasten both base assemblies together with (4) 12-24 screws (Item 4) and (4) 12-24
hex nuts (Item 5). Test that cams rotate freely on both sides of the door after tightening the
screws.
5. Install the push handle assembly (Item 7) to the base assembly installed on push side of door using
(2) socket head cap screws (Item 8). Insert (1) stop pin (Item 9) through the push base assembly on
the the same side of the direction the push handle is pointing. Test push handle for proper
operation to be sure stop pin was installed in appropriate base assembly hole.
6. Repeat Step #5 on the pull side of the door for the pull handle assembly (Item 6). Insert (1)
stop pin (Item 9) through the pull base assembly on the opposite side of the direction the pull
handle assembly is pointing. Test pull handle for proper operaton to be sure stop pin was
installed in appropriate base assembly hole.
7. Place covers (Item 10) over handles and fasten each cover with (2) 8-32 screws (Item 11).
PATENT PENDING
LR6000 INSTALLATION
11
6
NOTES
1. TRIM CAN BE MOUNTED UP, DOWN, HORIZONTALLY OR VERTICALLY.
2. VISION LITE MUST BE AT LEAST 6" FROM CENTERLINE OF TRIM.
Handle
Pointing
Direction
8
12
5
CAM SHAFT
LATCH CAM
ALL PREP MOUNTING HOLES
TO BE STRAIGHT & PARALLEL
TO ONE ANOTHER, THIS WILL
HELP PREVENT ANY BINDING
OF MECHANICAL PARTS.
1
NOTE:
BEFORE MOUNTING BASE ASSEMBLIES,
CAM MUST BE ROTATED AS PER DRAWING
SHOWN IN DETAIL "A".
3
4
12
9
13
* *
LEVERS
UP
**
ITEM QTY
1 1
2 2
3 2
4 4
5 4
6 1
7 1
8 4
9 2
10 2
11 4
12 2
13 1
3
Handle
Pointing
Direction
8
7
11
PULL
PUSH
PULL PUSH
LEVERS LEVERS
DOWN MIXED
c
PARTS LIST
DESCRIPTION
LATCH
#8 X 3/4"FHWS OR 8-32 X 3/8"FHMS UC
BASE ASSEMBLY
12-24 X 2-1/2" PTHMS
12-24 HEX NUT
HANDLE ASSEMBLY, PULL
HANDLE ASSEMBLY, PUSH
6-32 X 3/8" SHCS
STOP PIN
COVER
8-32 X 3/8" OVAL HEAD M.S.
COTTER PIN
7/64" ALLEN KEY
8
11
10
LEVERS LEVERS
HORIZONTAL HORIZONTAL
WITH 5" OR 7" BACKSET
BACKSET POINTING
POINTING HINGE EDGE
LOCK EDGE
LR6000-1-03.DWG
LR6000
PAGE 1 OF 3
REVISED 11-05-18