ABH 6100EO Series Installation

6100EO SERIES EXIT ONLY PUSH/PULL HANDLE
INSTALLATION RETROFIT FOR 161 PREP
(NO ADDITIONAL THRU BOLTS REQUIRED)
NOTES
1. TRIM CAN BE MOUNTED UP, DOWN, HORIZONTALLY OR VERTICALLY.
2. USES STANDARD 161 DOOR PREP.
3. VISION LITE MUST BE AT LEAST 6" FROM CENTERLINE OF TRIM.
SQUARE
-OR-
ROUND
COVER
13
CAM SHAFT
STAKING SCREW HOLE
NOTE:
BEFORE MOUNTING PUSH AND PULL
HANDLES, CAM PIN MUST BE ROTATED
TOWARDS SIDE INDICATED BY ARROW
STAMPED ON THE BASE.
DETAIL "A"
INSTALLATION INSTRUCTIONS:
1. Door to be machined for standard 161 .
2. Install latch (item 12) using either #8 FHWS (item 11) or 8-32 FHMS (item 2) depending on door material type.
3. Before mounting adapter plate (item 6) & exit only plate (item 8), determine which side of the door will receive the push or pull handle
assembly (item 4) and the direction the handle will mount. Handle can be mounted up, down or horizontally.
4. Mount adapter plate (item 6) & exit only plate (item 8) to door with (2) 12-24 screws (item 5) thru door and latch to (2) 12-24 sex
bolts (item 7). tighten securely.
5. Before mounting handle assembly (item 4), cam pin must be rotated towards the correct side of the handle (see detail A).
6. Mount handle assembly (item 4) to adapter plate (item 6) with (4) 10-32 screws (item 3) with (4) star washers (item 10).
7. Test lock for proper operation. If latch bolt does not extend or retract freely because of any type of binding, loosen mounting screws
to adjust alignment of trim handle assembly (item 4) and re-tighten screws one at a time while checking latch bolt movement.
8. To prevent the handle assembly from possible twisting, which in turn can cause binding, determine which staking screw hole will be
used for the handle assembly (the staking screw installs on the staking screw hole location opposite the direction the handle is
mounted). Install staking screw using #12 PHSMS (item 13).
9. Place cover (item 1) over handle assembly (item 4) and secure with (2) 8-32 screws (item 2) on each side.
PATENT No. 6,196,599 & 5,730,478
1
2
3
10
4
12
LATCH CAM
2
11
O www.abhmfg.com
R
E-mail: abhinfo@abhmfg.com
Architectural Builders Hardware Mfg., Inc.
1222 Ardmore Ave., Itasca, IL 60143
630.875.9900; FAX 800.9FAXABH (932.9224)
**
5
6
ALL PREP MOUNTING HOLES
TO BE STRAIGHT & PARALLEL
TO ONE ANOTHER, THIS WILL
HELP PREVENT ANY BINDING
OF MECHANICAL PARTS.
ITEM QTY PART DESCRIPTION
1
1
COVER
2 4
8-32 x 3/8" FHMS
3 4
10-32 x 1/4" PAN HD. M.S.
4
1
PUSH OR PULL HANDLE ASSY
5
2 12-24 x 1-7/8" FHMS
6 1
ADAPTER PLATE
7
2
12-24 x 1/2" SEX BOLT
8
1
EXIT ONLY PLATE
9
.
.
10 4
#10 STAR WASHER
11 2
#8 x 3/4" FHWS
12
1
LATCH
13
1
#12 x 1/2" PHSMS STAKING SCREWS
7
8
HANDLE
* * HORIZONTAL
HANDLES HANDLES
WITH 7"
UP DOWN
BACKSET
c 2017 ABH Mfg., Inc.
printed in USA
U
C US
L
R
CLASSIFIED
HANDLE
HORIZONTAL
WITH 5" OR 7"
BACKSET
6100EO-1-00.DWG
6100EO
PAGE 1 OF 3
ISSUED 06-08-17