Yamaha MU128 Sound List & Midi Data page 30

20 rr mm --
21 rr mm --
22 rr mm --
23 rr mm --
24 rr mm --
25 rr mm --
26 rr mm --
28 rr mm --
29 rr mm --
30 rr mm --
31 rr mm --
Drum low pass filter cutoff
frequency
rr: drum instrument note number
mm: 00 - 64 - 127
(-64...0...+63)
Drum low pass filter resonance
rr: drum instrument note number
mm: 00 - 64 - 127
(-64...0...+63)
Drum EG attack rate
rr: drum instrument note number
mm: 00 - 64 - 127
(-64...0...+63)
Drum EG decay rate
rr: drum instrument note number
mm: 00 - 64 - 127
(-64...0...+63)
The effect will apply both to
Decay 1 and 2.
Drum instrument pitch coarse
rr: drum instrument note number
mm: 00 - 64 - 127
(-64...0...+63)
Drum instrument pitch fine
rr: drum instrument note number
mm: 00 - 64 - 127
(-64...0...+63)
Drum instrument level
rr: drum instrument note number
mm: 00 - 127(0...maximum)
Drum instrument panpot
rr: drum instrument note number
mm: 00, 01-64-127(RND,
L63...C...R63)
Drum instrument reverb send
level
rr: drum instrument note number
mm: 00 - 127(0...maximum)
Drum instrument chorus send
level
rr: drum instrument note number
mm: 00 - 127(0...maximum)
Drum instrument variation
send level
rr: drum instrument note number
mm: 00 - 127(0...maximum)
(when Variation Connection
= SYSTEM))
mm: 00, 01-127 (OFF,ON)
(when Variation Connection
= INSERTION))
MU128 MIDI
36 rr mm --
48 rr mm --
49 rr mm --
52 rr mm --
53 rr mm --
MSB 14H-35H (for drums) is received when Multi Part
parameter PART MODE = DRUMS1...4.
*1 Refer to 1.2.4
*2 '--' indicates that the setting value is ignored.
*3 Adjusts the time after the note is played until vibrato
begins to take effect. The effect will begin more quickly
for higher values, and more slowly for higher values.
No effect if Bank Select MSB=127 is selected.
*4 No effect if Multi Part parameter PART MODE =
DRUM, DRUMS1...4.
1.2.22 RPN (Registered parameter number)
This message is used to specify part parameters such as Pitch
Bend Sensitivity or Tuning etc. as an offset value.
Use RPN MSB and RPN LSB to specify the parameter that
you wish to modify, and then use Data Entry (see 1.2.4) to
set the value of the specified parameter.
Control# Parameter
100 RPN LSB
101 RPN MSB
If the Multi Part parameter Rcv RPN = OFF, that part will
not receive this message.
The following RPN messages can be received.
RPN Data Entry*1
MSB LSB MSB LSB
00 00 mm -- *2
00 01 mm ll
MIDI data format
Drum high pass filter cutoff
frequency
mm: 00 - 64 - 127
(-64...0...+63)
Drum EQ bass gain
mm: 00 - 64 - 127 (-64...0...
+63)
Drum EQ treble gain
mm: 00 - 64 - 127
(-64...0...+63)
Drum EQ bass frequency
mm: 04 - 40(32...2.0k [Hz])
Drum EQ treble frequency
mm: 28 - 58(500...16.0k
[Hz])
Data Range
0...127
0...127
Parameter name and value range
Pitch bend sensitivity
mm: 00-24 (0...+24
semitones)
Specify up to 2 octaves in
semitone steps
Fine tuning
mm ll: 00 00 -100 cents
: :
mm ll: 64 00 0 cents
: :
mm ll: 127 127 +100 cents
31