Yamaha MOTIF RACK ES Owner's Manual page 91

MIDI
BasicRcvCh Basic Receive Channel
TransmitCh Transmit Channel
DeviceNo. Device Number
BankSelSw Bank Select Switch
PgmChangeSw
Program Change Switch
CC Mode Control Change Mode
RcvBulkSw Receive Bulk Switch
MIDI Sync MIDI Sync
MIDI IN/OUT MIDI In/Out
ThruPort
Through Port
PLG1Sys, PLG2Sys (Plug-in Board System)
PolyExpand
Poly Expand
DeviceNo. Device Number
PortNo. Port Number
RcvGM/XG Receive GM/XG
Native System Native System Parameter
Parameter
JobSel (Job Selection)
Determines the MIDI receive channel for the Voice/Performance mode.
Settings: 1~16, omni (all channels), off
n In the Multi mode, each Part receives MIDI data according to its assigned MIDI receive channel (Multi Part Edit
Voice display "ReceiveCh").
Determines the MIDI transmit channel for the Voice/Performance mode.
Settings: 1~16, off
n The Arpeggio output channel is determined by the Arpeggio Transmit Channel settings in each mode.
Determines the MIDI Device Number. This number must match the Device Number of the external MIDI
device when transmitting/receiving bulk data, parameter changes or other system exclusive messages.
Settings: 1~16, all, off
This switch enables or disables Bank Select messages, both in transmission and reception. When this is set
to "on," this synthesizer responds to incoming Bank Select messages, and it also transmits appropriate
Bank Select messages (when using the panel).
Settings: off, on
This switch enables or disables Program Change messages, both in transmission and reception. When this
is set to "on," this synthesizer responds to incoming Program Change messages, and it also transmits
appropriate Program Change messages (when using the panel).
Settings: off, on
Determines how this synthesizer receives and recognizes the AEG Sustain MIDI message. When set to
mode1, it is received as a Parameter Change. When set to mode2, it is received as a Control Change
message.
Settings: mode1, mode2
Determines whether or not Bulk Dump data can be received.
Settings: protect (not received), on (received)
Determines whether Arpeggio playback will be synchronized to the instrument's internal clock or an external
MIDI clock.
Settings: internal, MIDI
internal............. Synchronization to internal clock. Use this setting when the MOTIF-RACK ES is to be used alone.
MIDI ................. Synchronization to a MIDI clock received from an external MIDI instrument via MIDI. Use this setting when the
external MIDI device is to be used as master.
Determines which physical output terminal(s) will be used for transmitting/receiving MIDI data:
Settings: MIDI, USB
n The two types of terminals above cannot be used at the same time. Only one of them can be used to transmit/receive
MIDI data.
When using the USB terminal for MIDI transmission/reception, you can have this synthesizer respond to
MIDI data over one port, while relaying the data for another port number (you can set here) to a separate
tone generator (connected to the MIDI OUT terminal).
Settings: 1 ~ 8
These settings are available only when the Plug-in Board is installed to the MOTIF-RACK ES.
*The available Native System Parameters depends on each Plug-in Board.
This parameter is accessible only when you have two identical Plug-in Boards (except for the PLG150-DR/
PC) installed on the instrument. The "off" setting enables two or three boards to work separately (you can
select them in two or three different Parts). When this is set to "on," the two boards effectively function
together as one board (used in a single Part) — giving you double the amount of polyphonic notes you can
play at one time.
Settings: off, on
Determines the MIDI Device Number of the Plug-in Board. This number must match the Device Number of
the external MIDI device when transmitting/receiving bulk data, parameter changes or other system
exclusive messages.
Settings: 1~16, all, off
Determines the MIDI Port number over which the Plug-in Board receives MIDI data. One port can be set for
the Multi-part Plug-in Board and two ports can be set for the Single-part Plug-in Board.
Settings: off, 1~3
n For information on the Plug-in Board and the internal tone generator block, see page 52.
Determines whether "GM on" and "XG on" messages are recognized (on) or not (off). This parameter is
available only when a Multi-part Plug-in Board has been installed to slot 2.
Sets various Native System parameters for the Plug-in Board. For details on the parameters, refer to the
owner's manual of your particular Plug-in Board.
Voice/Performance/Multi mode [UTILITY]
The available functions are: Initialize, Copy, Bulk Dump, Plug-in Save, Plug-in Load, and Factory Set.
For details, see the section "Using the Jobs" on page 47.
JobSel display select Job with [MUTE/SEL/ENTER]
Utility
91
Owner's Manual