Yamaha MOTIF RACK ES Owner's Manual page 80

Performance mode Performance Edit
Low/LowMid/Mid/ Frequency
HighMid/High Freq
Low/LowMid/Mid/ Gain
HighMid/High Gain
Low/LowMid/Mid/ Frequency Characteristic
HighMid/High Q
MEF (Master Effect)
Switch Switch
Type Type
CtrlAsn (Control Assign)
BC Breath Controller
RB Ribbon Controller
AS1/AS2 Assign
FC1/FC2 Foot Controller
Output
Volume Volume
Pan Pan
RevSend/ChoSend Reverb Send/Chorus Send
EG (Envelope Generator)
AEG Attack/Decay/ AEG Attack Time/Decay Time/
Sustain Level/Release Time
Sustain/Release
FEG Attack/Decay/ FEG Attack Time/Decay Time
/Release Time/Depth
Release/Depth
Cutoff/Resonance Cutoff/Resonance
Part Edit
These parameters are for editing the individual Parts that make up a Performance.
n You can switch between Part 1 and Plug-in Part 1 with the [1/5/9/13] button, and between Part 2 and Plug-in Part 2 with the [2/6/10/14] button.
Voice
PartSw Part Switch
Bank Bank
Number
Number
Mono/Poly (Mode) Mono/Poly
ArpSwitch (ArpSw) Arpeggio Switch
80
Owner's Manual
Determines the center frequency. Frequencies around this point are attenuated/boosted by the Gain setting.
Settings:
LOW: Shelving 32Hz ~ 2.0kHz, Peaking 63Hz ~ 2.0kHz
LOWMID, MID, HIGHMID: 100Hz ~ 10.0kHz
HIGH: 500 Hz ~ 16.0 kHz
Determines the level gain for the Frequency (set above), or the amount the selected frequency band is
attenuated or boosted.
Settings: -12dB ~ 0dB ~ +12dB
This varies the signal level at the Frequency setting to create various frequency curve characteristics.
Settings: 0.1 ~12.0
Determines the Master Effect of each Performance. With the exception of the two below, the available
parameters differ depending on the currently selected effect type. Refer to the separate Data List for details.
Turns the Master Effect on/off.
Settings: on, off
Determines the Master Effect type.
Settings: Refer to the separate Data List booklet.
Determines the Control Numbers corresponding to the external controllers. For details, see page 46.
Determines the Control Number corresponding to the Breath Controller.
Determines the Control Number corresponding to the Ribbon Controller.
Determines the Control Number corresponding to Assign 1/2.
Determines the Control Number corresponding to the Foot Controller.
Determines the output level of the selected Performance. You can adjust the overall volume, keeping the
balance between all Parts.
Settings: 0 ~ 127
Determines the stereo pan position of the selected Performance. This parameter offsets the same parameter
in the Part edit setting. A setting of "C" (center) maintains the individual Pan settings of each Part.
Settings: L63 (far left) ~ C (center) ~ R63 (far right)
Determines the Send level of the signal sent from Insertion Effect 1/2 (or the bypassed signal) to the Reverb/
Chorus Effect.
Settings: 0 ~ 127
This display contains the basic EG settings, both volume and filter, as well as the filter's Cutoff Frequency
and Resonance settings. The settings made here are applied as offsets to the AEG and FEG settings in the
Part Edit mode.
Settings: -64 ~ 0 ~ +63
[SHIFT]+[PERFORM] select Performance
[MUTE/SEL/ENTER] (LED turns off)
[E][F]
You can select a Voice for each Part.
Determines each Part to on or off. Since a Performance can consist of up to four Parts, you can select four
Parts from Parts 1 - 4 and the Plug-in Parts 1 - 2. Please note that "(on)" is displayed if selecting more than
four Parts. "(on)" indicates no available Part.
Settings: on, off
Determines the Voice Bank and Voice Number for each Part. For details about the Plug-in Voice, refer to the
owner's manual for your Plug-in Board.
Selects monophonic or polyphonic playback for each Part. Select whether each Part is played back
monophonically (single notes only) or polyphonically (multiple simultaneous notes).
Settings: mono, poly
n This parameter is not available for the Part to which the Drum Voice is assigned.
Determines whether Arpeggio is on or off for the currently selected Part.
Settings: on, off
select Performance Edit by pressing [EDIT] once or twice
select Part with [1/5/9/13]-[4/8/12/16] select each display with PAGE