Editing Effect Programs; Effect Blocks - Yamaha GW33 Owner's Manual

EDITING EFFECT PROGRAMS

OPERATION
1
Select an effect program for editing and press the
e button to enable the Edit mode.
(The EDIT/COMPARE lamp lights and the ON/OFF
lamp above Pedal Switch B flashes.)
2
Use Pedal Switches 1 – 5 to turn on the desired

effect blocks.

Since you'll probably want to listen to the
HINT
changes as you make them, make sure that all
relevant effect blocks are turned on. Better yet, turn off
all blocks except the one you are editing. This lets you
clearly hear only the effect you wish to edit. (One
possible exception to this guideline is the Amp Simula-
tor effect, changes to which are easier to hear when
Distortion is also on.)
•••••• YES
• •
• •
• •
• •
• •
•••••
• •
• •
• •
• •
• •
NO
••••••
Use these to select
the desired block
for editing. (In this
example, EQ/AMP
is selected.)
18
Effect programs can be edited in the Edit mode. Once you've edited a program, you can save it
to a User memory location. (See SAVING EFFECT PROGRAMS on page 31.)
Be careful not to press the p button at any time during editing. Doing so
CAUTION!
will call up the original effect program's settings and erase all settings you had made to that
point.
COMP — — — — - - -
DIST / 1~3 OD, DIST1,2 (DI*+AN) 4,5 OD*+DIST1,2
INSERT 6~11 OD, DIST1,2+INSERT 12 INSERT
EQ / AMP 1 EQ / 2 STACK 3 COMBO
1 CHORUS / 2 FLANGER 3 PHASER
MOD 1
4 PITCH SHIFT / 5 DETUNE
MOD 2
6 EXCITER / 7 TOUCH WAH 8 PEDAL WAH
DELAY — — — — - - -
REVERB 1 HALL 2 ROOM 3 STAGE
N.GATE/UTIL — — — — - - -
TUNER/ TUNING PITCH
METRONOME (0~5 = 440~445Hz)
PARAM COPY / SWAP / WRITE
• •
• •
•••••••••••••••••••••• •••••••••••••••••••••••••••••••••••••••••••••••••
• •
CHECK MEMORY NO.
Selects the type of
effect. (In this
example, 1 EQ is
selected.)
Adjusts the LOW parameter for the
EQ effect. (The dash indicates that
no parameter is available for the
other effects.)
1 2
3 Use the y and n buttons to select the
1 2 1 2
1 2
1 2
desired effect block row (in the parameter matrix
1 2 1 2
1 2
1 2 1 2 printed on the panel). (The lamp at the left of the
1 2
1 2
corresponding block lights.)
1 2 1 2
1 2
1 2
1 2 1 2
1 2 NOTE
1 2
1 2 1 2
selected in the Edit mode.
1 2
1 2
1 2 1 2
1 2
4
1 2
Use the Parameter Dials to adjust the effect param-
1 2 1 2
1 2
eters.
1 2 1 2
1 2 1 2
1 2 1 2
1 2 1 2
Parameter Dial A is used to change the effect type of
1 2 1 2
the selected block; B – E are used to change the
1 2 1 2
1 2 1 2
corresponding parameters.
1 2 1 2
1 2 1 2
1 2 1 2
In the example shown below, the EQ/AMP block has
1 2 1 2
1 2 1 2
been selected.
1 2 1 2
1 2
ATTACK SENSE
PRE-DRIVE* DRIVE
4 TUBE LOW / — MID / —
SPEED DEPTH
PITCH / PITCH L — / PITCH R
ENHANCE / SENSE FREQUENCY
TIME FB
4 PLATE TIME TONE
THRESHOLD VOLUME POSITION
BEAT
—
(14~88 = 1/4~8/8)
A B C
Adjusts the MID parameter
for the EQ effect. (The dash
indicates that no parameter
is available for the other
effects.)
The TUNER/METRONOME row cannot be
— LEVEL
TONE LEVEL
HIGH / TONE LEVEL
TONE / FB
ON/OFF
MIX
(SWITCH 4)
MIX / RANGE
MIX
ON/OFF
(SWITCH 5)
MIX
MINIMUM VOLUME TOTAL LEVEL
TEMPO CLICK LEVEL
(60~86.=60~186) (1 LO 2 MID 3 HI)
D E
Adjusts
the LEVEL
parameter.
Adjusts the HIGH
parameter for the EQ effect
and the TONE parameter
for the others.