EDITING AN EFFECT PROGRAM AND SAVING IT
1
Select one of the User or Preset effect programs.
Although any effect program will do, select
program number 11 for this example.
ON OFF
COMPRESSOR
HOLD
Press the Bank (B) Pedal Switch once, and press Pedal
Switch 1 to select Bank 1. Then, press Pedal Switch 1
again (if needed) to select program number 11.
Even though creating and saving your own
NOTE
effect program erases the previously stored program,
you can restore that particular factory Preset pro-
gram. Refer to RESTORING FACTORY-SET
EFFECT PROGRAMS on page 33 for details. Keep
in mind, however, that restoring the factory Preset
program will irretrievably erase the effect you've
created. For this reason, you may want to keep a
written record of the settings you make (using a copy
of the Blank Effect Parameter Chart on page 38), so
that you can reprogram the effect later if necessary.
2
Next, press the e button to enable
the Edit mode. (The EDIT/COMPARE lamp
lights and the ON/OFF lamp above the Bank Pedal
Switch flashes.)
EDIT/
COMPARE
Notice that the ON/OFF lamp above the Bank Pedal
Switch flashes. This means that you can turn indi-
vidual effect blocks on and off.
3
Try turning an effect block on and off now; press
Pedal Switch 2 to turn the Distortion block on or
off.
DIST / INSERT
Press this to turn Distortion
block on or off. (The lamp
lights when the block is on.)
The GW33 makes it extremely easy to adjust or change the sound of the effects. In this section,
you'll learn how to change the effect type and use the Parameter Dials to change effect settings.
You'll also learn how to compare the edited program with the original. Finally, you'll learn how
save the new effect program you've created.
Editing an Effect Program
COMPRESSOR
BANK MEMORY
Press this.
ON
DIST / INSER
OFF
DIST / INSER
1
1 1
1
1
NOTE
1 1
1
Delay/Reverb blocks is determined by the On/Off
1 1
1
parameter of those blocks. (See pages 24 and 27.)
1
1 1
1
1
4
1 1
Use the y and n buttons to select the
1
1
1 1
desired effect block row (in the parameter matrix
1
1
printed on the panel). (The lamp at the left of the
1 1
•••••••
1
1
corresponding block lights.) For this example, press
1 1
1
either button repeatedly until the Distortion/Insert
1 1
1 1
block is selected.
1 1
1 1
1 1
1 1
YES
••••••
• •
• •
• •
1 1
• •
• •
•••••
• •
• •
1 1
• •
• •
• •
••••••
NO
1 1
1 1
1 1
1 1
1 1
1 1
1 1
1 1
1 1
1 1
1 1
NOTE
1 1
selected in the Edit mode.
1 1
1 1
1 1
5
1 1
Use the Parameter Dials to adjust the effect
1 1
parameters. For example, if you want to change the
1 1
1 1
amount of Pre-drive in the Distortion effect (selected
1 1
1 1
above), adjust Parameter Dial B.
1 1
1 1
1 1
1 1
1 1
1 1
1 1
1 1
1 1
1 1
Parameter Dial A is used to change the effect type of
1 1
1 1
the selected block; B – E are used to change the
1 1
1 1
corresponding parameters.
1 1
1 1
6
1 1
If you wish, you can simply view the parameter
1 1
1 1
values that you are currently editing (without
1 1
changing them) by using the Parameter Check
1 1
1 1
mode. (See page 19 for details.)
1 1
1 1
1 1
1
For information about each of the effects and their
1 1
1
parameters, refer to the section EFFECTS AND
1 1
1
PARAMETERS on page 20.
1 1
1
1 1
1
1
The on/off switching of the MOD 1/2 and
COMP
DIST /
INSERT
• •
PARAM
• •
••••••••••••••••••••••
• •
CHECK
EQ / AMP
MOD 1
MOD 2
The TUNER/METRONOME row cannot be
B
— — — — - - -
1~3 OD
6~11 OD
1 EQ /
1 CHOR
4 PITCH
6 EXCIT
13