Table of Contents
Advertisement
Failure to follow these rules may result in serious personal injury or death.
IMPORTANT: Before switching the bandsaw on, ALWAYS check the machine for the correct setting and speed.
1. BEFORE OPERATING THE TOOL READ THE MANUAL! Learn
the machine's application and limitations, plus the specific hazards
particular to it.
2. ALWAYS USE SAFETY GLASSES (must be ANSI approved)
Everyday eyeglasses usually are only impact resistant and safety
glasses only protect eyes. A full-face shield will protect the eyes and
face.
3. WEAR PROPER APPAREL. Do not wear loose clothing, gloves,
neckties, rings, bracelets, or other jewelry which may get caught in
moving parts. Nonslip footwear is recommended. Wear protective
hair covering to contain long hair.
4. USE EAR PROTECTORS. Use earmuffs for extended period of
operation. Use muffs rated to 103 DBA LEQ (8 hour).
5. DO NOT USE IN DANGEROUS ENVIRONMENT. Do not use
power tools in damp or wet locations or expose them to rain. Keep
work area well lighted. The NOVA ECLIPSE is intended for indoor
use only. Failure to do so may void the warranty.
6. KEEP WORK AREA CLEAN. Cluttered areas/benches invite
accidents.
7. KEEP CHILDREN AND VISITORS AWAY. The NOVA ECLIPSE is
not recommended for children and ailing persons. Such personnel
and onlookers should be kept a safe distance from work area.
8. MAKE WORKSHOP CHILDPROOF with locks, master switches, or
by removing starter keys.
9. GROUND ALL TOOLS. If the tool is equipped with a three-prong
plug, it should be plugged into a three-hole electrical receptacle.
Never remove the third prong and add surge protection.
10. MAKE SURE TOOL IS DISCONNECTED FROM POWER
SOURCE whilst in service/maintenance mode.
11. DISCONNECT TOOLS FROM WALL SOCKET before servicing and
when changing accessories such as blades, components, fuses, etc.
12. AVOID ACCIDENTAL STARTING. Make sure switch is in the "Off"
position before plugging in power cord.
13. NEVER LEAVE MACHINE RUNNING UNATTENDED. Do not leave
machine unless it is turned off and has come to a complete stop.
14. KEEP GUARDS IN PLACE and in working order.
15. USE CORRECT TOOLS. Do not use a tool or attachment to do a
job for which it was not designed.
16. USE RECOMMENDED NOVA ACCESSORIES. The use of improper
accessories may cause hazards.
GENERAL SAFETY RULES
WARNING!
17. DO NOT FORCE THE TOOL. It will do the job better and be safer
at the rate for which it was designed.
18. MAINTAIN TOOLS IN TOP CONDITION. Keep tools sharp and
clean for best and safest performance. Follow instructions for
lubricating and changing accessories.
19. NEVER STAND ON TOOL. Serious injury could occur if the tool is
tipped or if the cutting tool is accidentally contacted.
20. REMOVE ADJUSTING KEYS AND WRENCHES. Form a habit of
checking to see that keys and adjusting wrenches are removed from
tool before turning it on.
21. DO NOT OVERREACH. Always keep proper footing and balance.
22. DIRECTION OF FEED. Mind the direction of blade to ensure a safe
environment.
23. PAY ATTENTION TO YOUR WORK. Concentrate on your work. If
you become tired or frustrated, leave it for a while and rest.
24. SECURE WORK. Use clamps or the vice to hold work when
practical. Severe injury or death can occur if an object comes free
as it can become a dangerous projectile.
25. CHECK DAMAGED PARTS. Before further use of the tool, any part
that is damaged should be carefully checked to ensure that it will
operate properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts, mounting, and
any other conditions that may affect its operation. Any damaged part
should be properly repaired or replaced.
26. DRUGS, ALCOHOL, MEDICATION. Do not operate machine while
under the influence of drugs, alcohol, or any medication.
27. DO NOT MODIFY OR USE THE BANDSAW FOR USES OTHER
THAN FOR WHICH IT WAS DESIGNED.
Advertisement
Table of Contents
