[Midi1] Transmit; Bankmsb Banklsb; [Midi2] Volume Pan Ctrl# / Value; R63 - Yamaha DTXTREME IIs Owner's Manual

[MIDI1], [MIDI2] & [MIDI3] MIDI Setup
Use these three pages to make settings for a MIDI ensemble
using the built-in tone generator or external sound modules.
The setting data will be sent to MIDI parts internally or
externally (via MIDI OUT or USB) when you recall and play
the drum kit you are currently editing.

[MIDI1] Transmit

PC#
Ch=10 on 001
1 2 3
[MIDI2] Volume Pan
Ch=10 127

R63

5 6

[MIDI3] RevSend ChoSend

Ch=10 127 127
8 9
1 Ch=
Determines the target MIDI channel (1 to 16).
2 Transmit
Determines the MIDI events that will be sent out over the
target channel 1.
❏ Settings:
• off: Sends no MIDI events. All following parameters cannot be
set and "---" is shown in the display.
• all: Sends both Program Change and Control Change, and all
following parameters become accessible.
• PC: Sends only Program Change, and parameters related to
Program Change become accessible. Parameters related to
Control Change (in the 2nd and 3rd screens) are disabled.
n When sending and setting only Program Change (Transmit=PC),
you can also use Bank Select (a Control Change event).
3 PC#
Determines the program number to be transmitted. If used
for the built-in tone generator, this specifies a GM voice.
❏ Settings: 001~128
n If you set a program number for channel 10 (Ch = 10), it will be
only sent out externally via MIDI OUT or USB. Since it is not sent
to the built-in tone generator, your drum kit will not be affected.
4 BankMSB & BankLSB
If you use an external sound module that has multiple sound
banks, you can use these two events for selecting a bank. In
combination with the program number parameter 3, you
can select a specific sound program. However, you do not
need to use these two events for the built-in tone generator
since it has no banks.
❏ Settings: 000~127 (for both MSB and LSB)

BankMSB BankLSB

000 000
4
Ctrl# / Value
127 127
7
54
5 Volume
Determines the value for the controller number 007
(volume). If used for the built-in tone generator, this affects
the volume of each part.
❏ Settings: 000~127
6 Pan
Determines the value for the controller number 010 (pan).
If used for the built-in tone generator, this affects the stereo
panning of each part.
❏ Settings: 000~064~127 (left to center to right)
7 Ctrl# & Value
Control Change is MIDI information used to control the
performance of a MIDI device. You can control a variety of
functions pre-defined as controller numbers and their control
values. These two parameters let you create a specific Control
Change event by setting the controller number (Ctrl#) and
control value (Value).
❏ Settings: ---, 000~127 (Ctrl#), 000~127 (Value)
n Selecting "---" for Ctrl# will automatically set "---" for Value,
disabling this feature.
8 RevSend
Determines the value for the controller number 091 (effect
depth). If used for the built-in tone generator, this specifies
the master send level to the reverb effect (system effect) for
each part.
❏ Settings: 000~127
9 ChoSend
Determines the value for the controller number 093 (effect
depth). If used for the built-in tone generator, this specifies
the master send level to the chorus effect (system effect) for
each part.
❏ Settings: 000~127
n If you set a Control Change event 7 that duplicates the Volume 5,
Pan 6, RevSend 8, or ChoSend 9 setting, the Control Change
event 7 will take priority.
Once you've finished making the desired voice
settings, store this drum kit (page 35).