Table of Contents
Advertisement
Quick Links
Your safety and the safety of others is very important.
▪
In order to help you make informed decisions about safety, we have provided
installation instructions and other information.
▪
These instructions alert you to potential hazards that could hurt you or others.
▪
Please do a job safety analysis before each task to identify potential hazards for your
situation and remove/protect against them.
▪
You must use your own good judgment, and take your time.
Read and understand all safety precautions and instructions before installing this product.
THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR
INSTALLATION AND USE RESTS WITH THE OWNER.
CARELESS INSTALLATION AND OPERATION CAN RESULT IN SERIOUS INJURY
Failure to observe these instructions could lead to severe injury or death.
❑
❑
Always remove jewelry and wear eye protection.
❑
❑
Always use extreme caution when jacking up a vehicle for work. Set
emergency brake and use tire blocks. Locate and use the vehicle
manufacturers designated lifting points. Use jack stands.
❑
❑
Always use appropriate and adequate care in lifting components into place.
❑
❑
Always ensure components will remain secure during installation and
operation.
❑
❑
Always wear safety glasses when installing this kit. A drilling operation will
cause flying metal chips. Flying chips can cause serious eye injury.
❑
❑
Always use extreme caution when drilling on a vehicle. Thoroughly inspect
the area to be drilled (on both sides of material) prior to drilling, and
relocate any objects that may be damaged.
❑
❑
Always use extreme caution when cutting and trimming during fitting.
❑
❑
Always tighten all nuts and bolts securely per installation instructions.
❑
❑
Always route electrical cables carefully. Avoid moving parts, components
that become hot and rough or sharp edges.
❑
❑
Always insulate and protect all exposed wiring and electrical terminals.
❑ Always perform regular inspections and maintenance on mounts and
❑
related hardware.
Copyright 2008 Fab Fours, Inc.
Installation Instructions
GMC Canyon Premium Front Bumper
Product Number: H3450, H3451, H3452
Application: 2015-2018 GMC CANYON
SAFETY
OR EQUIPMENT DAMAGE.
Injury hazard
Page 1 of 15
H345X_REV_A
Advertisement
Table of Contents
Related Manuals for Fab Fours H3450
Summary of Contents for Fab Fours H3450
- Page 1 Installation Instructions GMC Canyon Premium Front Bumper Product Number: H3450, H3451, H3452 Application: 2015-2018 GMC CANYON SAFETY Your safety and the safety of others is very important. ▪ In order to help you make informed decisions about safety, we have provided installation instructions and other information.
- Page 2 Installation Instructions GMC Canyon Premium Front Bumper Product Number: H3450, H3451, H3452 Application: 2015-2018 GMC CANYON Overview Congratulations on your new purchase of the industries’ best and most stylish front bumper available for the 2015 GMC Canyon! This bumper has been engineered for strength while keeping the weight down.
-
Page 3: Parts List
Installation Instructions GMC Canyon Premium Front Bumper Product Number: H3450, H3451, H3452 Application: 2015-2018 GMC CANYON Parts List • H345X replacement bumper and brackets • 50055-HW fastener kit • HDLA-HW • 4 Stud plates • Light kitting [i.e. 20090(2), 61737(2), 61738(2), 61675(2), 20995, 20996] •... - Page 4 Installation Instructions GMC Canyon Premium Front Bumper Product Number: H3450, H3451, H3452 Application: 2015-2018 GMC CANYON C. Using a 10 mm socket, remove two additional bolts (one per side) holding the front bumper to the truck from beneath. D. Using a 10mm socket and extensions, go through the grill and remove the two bolts holding it to the vehicle.
- Page 5 Installation Instructions GMC Canyon Premium Front Bumper Product Number: H3450, H3451, H3452 Application: 2015-2018 GMC CANYON E. Using a 7mm socket, remove the three bolts per side holding the bumper to the fender. Page 5 of 15 H345X_REV_A Copyright 2008 Fab Fours, Inc.
- Page 6 Installation Instructions GMC Canyon Premium Front Bumper Product Number: H3450, H3451, H3452 Application: 2015-2018 GMC CANYON F. Remove the 9 clips holding the upper engine cover above the grill. Page 6 of 15 H345X_REV_A Copyright 2008 Fab Fours, Inc.
- Page 7 Installation Instructions GMC Canyon Premium Front Bumper Product Number: H3450, H3451, H3452 Application: 2015-2018 GMC CANYON Using a T-15 TORX, remove 6 bolts holding the grill to the vehicle. H. Remove the grill and bumper as one piece and detach the grill from the bumper by releasing the clips.
-
Page 8: Pre-Installation
Installation Instructions GMC Canyon Premium Front Bumper Product Number: H3450, H3451, H3452 Application: 2015-2018 GMC CANYON III. Pre-Installation NOTE: The following installation steps apply to the installation of the front bumper. PLEASE READ THE ENTIRE MANUAL BEFORE ATEMPTING INSTALLATION. Ignoring these steps will increase your probability of scratching the vehicle during product installation. - Page 9 Installation Instructions GMC Canyon Premium Front Bumper Product Number: H3450, H3451, H3452 Application: 2015-2018 GMC CANYON The fog light wiring may be installed at this time. To do so, connect wiring to fog light and tap into OEM fog light wiring using supplied tap connectors.
- Page 10 Product Number: H3450, H3451, H3452 Application: 2015-2018 GMC CANYON Install the Fab Fours fog lights onto the mounting brackets as shown below using the #8 button head screws, washers, and hex nuts. Install the fog light and bracket into the bumper using the remaining two holes available in the light insert.
- Page 11 M8000 winch and control box. Other winches may be used, but they may require relocation of the control box or cutting of the vehicle. Fab Fours is NOT responsible for any damage you do to your truck if you choose to cut or alter your vehicle in any way.
- Page 12 Installation Instructions GMC Canyon Premium Front Bumper Product Number: H3450, H3451, H3452 Application: 2015-2018 GMC CANYON If not installing a winch, a license plate may be installed onto the front face of the bumper. Page 12 of 15 H345X_REV_A Copyright 2008 Fab Fours, Inc.
-
Page 13: Front Bumper Installation
Installation Instructions GMC Canyon Premium Front Bumper Product Number: H3450, H3451, H3452 Application: 2015-2018 GMC CANYON IV. Front Bumper Installation Mount bracket to truck frame. Use the OEM hardware to secure brackets. They may be tightened at this time. Install the provided stud plates from inside the winch tray with the threads pointing to the rear of the vehicle. - Page 14 Allow 0.375” of clearance to all painted surfaces if possible. This is to allow for frame flex! Fully tighten all fasteners between bumper and brackets. Enjoy your new front replacement bumper from Fab Fours! Page 14 of 15 H345X_REV_A...
-
Page 15: Maintenance & Care
Installation Instructions GMC Canyon Premium Front Bumper Product Number: H3450, H3451, H3452 Application: 2015-2018 GMC CANYON Maintenance/Care ❑ Periodically check and tighten all fasteners. ❑ ❑ Stripped, fractured, or bent bolts or nuts need to be replaced. ❑ ❑ After washing of the vehicle make sure to fully dry all surfaces ❑...