Digital Performer; Sonar - Yamaha 01X Software Installation Manual

Audio setup
1
Select [Options] [Preferences]
[Install] from the menu. A window for setup appears.
2
(Windows only) Click the Audio Driver 2 tab, then check (select) ASIO for
the driver.
3
Select "ASIO mLAN" for the device, then restart Logic.
Playing the demo song (Macintosh only)
1
Install the Vocal Rack, Final Master and Pitch Fix Plug-in Effects (page
23).
2
Copy the "DemoSong" folder of the CD-ROM to your hard disk.
3
Double click on the demo song file (All for you for Logic) in the
"DemoSong" folder to open the demo song file.
4
The steps following this are the same as those following step 3 of playing
the demo song on the SQ01 (page 26).

Digital Performer

Remote Control setup
1
Pull down the [Basics] menu and select [Control Surface Setup] to call up
the "Control Surface" window.
2
Select "Mackie Control" in the Driver section. If Mackie Control is not
available here, see the supplementary instructions below.
3
In the box for setting "Unit" and "MIDI," select "Mackie Control" in the
"Unit" section and select the DAW/Port 1 (mLAN MIDI In/Out Port 1) in
the "MIDI" section.
4
On the 01X, select UTILITY
"DP," then enter the Remote mode by pressing the [REMOTE] button.
When you cannot select "Mackie Control" in step 2:
1
Download the Mackie Control Plug-in software from
"www.motu.com" and save it to your hard disk.
2
Move the Mackie Control file to the "Plug-ins" folder contained in the
folder to which Digital Performer has been installed.
3
Start Digital Performer.
• Set the MIDI Thru function of OMS Setup and the MIDI Patch Thru function of
Digital Performer so that they function in the background.
Audio setup
1
Pull down the [Basics] menu and select [Configure Audio System]
[Configure Hardware Driver] to call up the "Configure Hardware Driver"
window.
2
Select "ASIO" from the menu.
3
Select ASIO mLAN for the "ASIO Driver."
• To call up the ASIO mLAN Control Panel, click "Configure Driver."
28
TOOLS for 01X/Plug-in Effect Installation Guide
[Audio Hardware & Drivers]
REMOTE (knob 1) REMOTE SELECT

SONAR

Remote Control setup
1
Pull down the [Options] menu and select [MIDI Devices] to call up the
"MIDI Devices" window.
2
Add "mLAN MIDI In (Port 1)" to the "Inputs" and add "mLAN MIDI Out
(Port 1)" to the "Outputs."
3
Pull down the [Options] menu and select [Control Surfaces] to call up the
Control Surface window.
4
Click the "New" icon, select "Mackie Control" in [Control Surfaces] then
set the Input Port to "mLAN MIDI In (Port 1)" and the Output Port to
"mLAN MIDI Out (Port 1)."
5
On the 01X, select UTILITY
"SONAR," then enter the Remote mode by pressing the [REMOTE]
button.
Audio setup (WDM)
• If the WDM setting (for SONAR) is not specified set Mode in Driver Setup (page 10) to
WDM after closing the application.
1
Select Options Audio to open the "Audio Options" window.
2
Click Advanced tab to make sure the Driver Mode is set to WDM/KS.
• If WDM/KS is not selected, select "WDM/KS," then restart the SONAR.
3
Select Options Audio to open the "Audio Options" window, then select
mLAN audio ports to be used from "General"
"Drivers."
Playing the demo song
4
Copy the folder of the demo song from the CD-ROM to C:\Program
Files\YAMAHA on your computer.
If there is no Program Files folder in the C: drive of your computer, or the
Yamaha software has been installed to a different folder and you need
copy the demo song to some other folder location, make sure to establish
again the necessary file link (as described in the note below), since the
link between the demo song file and audio files has been broken.
5
From the File menu, select [Open] call up the [Open] dialog box.
Select "All for You for Cubase SXSL" from the demo song folder you
have copied to the hard disk, and click [Open].
• If a message appears indicating that the file cannot be found, select the specified
file in the demo song folder you have copied to the hard disk.
6
The steps following this are the same as those following step 3 of playing
the demo song on the SQ01 (page 26).
REMOTE (knob 1) REMOTE SELECT
"Input Monitoring"