Gree GWH07AFAXA-K3NNA1A Service Manual page 49

/ " "button to adjust fan blowing angle. (Cooling only unit won't
receive heating mode signal. If setting heat mode with remote
controller, press ON/OFF button can't start up the unit).
Note:
● For preventing cold air, after starting up heat mode,indoor unit
will delay 1~5 minutes to blow air (Actual delay time depends on
indoor ambient temperature).
● Set temperature range from remote controller:
61-86 o F(16~32ºC).
button
Pressing this button can set fan speed circularly as: auto (AUTO),
low( ), medium( ), high(
Note:
● Under AUTO speed, air conditioner will select proper fan speed
automatically according to factory default setting.
● It's low fan speed under dry mode.
TURBO button
Under COOL or HEAT mode, press this button to turn to quick
COOL or quick HEAT mode. "
controller. Press this button again to exit turbo function and "
" icon will disappear. If start this function, the unit will run at
super-high fan speed to cool or heat quickly so that the ambient
temperature approaches the preset temperature as soon as
possible.
/ button
● Press " " or " " button once increase or d ecrease set
temperature 1°F (°C). Holding "
temperature on remote controller will change quickly. On releasing
button after setting is finished, temperature indicator on indoor unit
will change accordingly.
● When setting T-ON, T-OFF or CLOCK, press " " or " " button
to adjust time. (Refer to CLOCK, TON,T-OFF buttons)
button
Press this button can select left & right swing angle. Fan blow
angle can be selected circularly as below:
Note:
● Press this button continuously more than 2s, the main unit will
swing back and forth from left to right, and then loosen the button,
the unit will stop swinging and present position of guide louver will
be kept immediately.
● Under left and right swing mode, when the status is switched
46
).
" icon is displayed on remote
" or " " button, 2s later, set
from off to , if press this button again 2s later,
will switch to off status directly; if press this button again within
2s, the change of swing status will also depend on the circulation
sequence stated above.
● The function is only available for some models.
button
Press this button can select left & right swing angle. Fan blow
angle can be selected circularly as below:
no display
(horizontal louvers stops
at current position)
● When selecting " ", air conditioner is blowing fan
automatically. Horizontal louver will automatically swing up &
down at maximum angle.
●When selecting "
、 、 、 、
at fixed position. Horizontal louver will stop at the fixed position.
● When selecting "
、 、
fixed angle. Horizontal louver will send air at the fixed angle.
● Hold " "button above 2s to set your required swing angle.
When reaching your required angle, release the button.
Note:
● " " may not be available. When air conditioner receives
、 、
this signal, the air conditioner will blow fan automatically.
● Press this button continuously for more than 2s, the main
unit will swing back and forth from up to down, and then loosen
the button, the unit present position of guide louver will be kept
immediately.
● Under up and down swing mode, when the status is switched
from off to , if press this button again 2s later,
switch to off status directly; if press this button again within 2s,
the change of swing status will also depend on the circulation
sequence stated above.
button
T-ON T-OFF
● T-ON button
"T-ON" button can set the time for timer on. After pressing this
button, " " icon disappears and the word "ON" on remote
controller blinks. Press " " or "
After each pressing " " or "
or decrease 1min. Hold " " or "
change quickly until reaching your required time. Press "T-ON" to
confirm it. The word "ON" will stop blinking. "
displaying. Cancel T-ON: Unde the condition that T-ON is started
up, press "T-ON " button to cancel it.
● T-OFF button
"T-OFF" button can set the time for timer off. After pressing this
button, " " icon disappears and the word "OFF" on remote
controller blinks. Press "
setting. After each pressing "
will increase or decrease 1min. Hold " " or "
the time will change quickly until reaching your required time.
Press "T-OFF" word "OFF" will stop blinking. "
Service Manual
", air conditioner is blowing fan
", air conditioner is blowing fan at
status will
" button to adjust T-ON setting.
" button, T-ON setting will increase
" button, 2s later, the time will
" icon resumes
" or " " button to adjust T-OFF
" or " " button, T-OFF setting
" button, 2s later,
" icon resumes
Technical Information
status