Gree GWH07AFAXA-K3NNA1A Service Manual page 46

Service Manual
Under Cool, Dry or Heat mode, press this button to turn on Sleep
function.
Press this button again to cancel Sleep function.
Under Fan and Auto modes, this function is unavailable.
button
Press this button, you can see indoor set temperature, indoor
ambient temperature on indoor unit's display. The setting on
remote controller is selected circularly as below:
NOTE:
● Outdoor temperature display is not available for some models.
At that time, indoor unit receives "
indoor set temperature.
button
Under cool or heat mode, press this button to turn to quick cool
or quick heat mode. " " icon is displayed on remote controller.
Press this button again to exit turbo function and "
disappear.
button
Press this button to start I FEEL function and "
displayed on the remote controller. After this function is set, the
remote controller will send the detected ambient temperature
to the controller and the unit will automatically adjust the indoor
temperature according to the detected temperature. Press this
button again to close I FEEL function and "
Please put the remote controller near user when this function
is set. Do not put the remote controller near the object of high
temperature or low temperature in order to avoid detecting
inaccurate ambient temperature. When I FEEL function is turned
on, the remote controller should be put within the area where
indoor unit can receive the signal sent by the remote controller.
button
● Under ON status, press this button to set timer OFF; Under OFF
status, press this button to set timer ON.
● Press this button once and the characters of HOUR ON (OFF)
will flash to be displayed. Meanwhile, press "▲" button or "▼"
button to adjust timer setting (time will change quickly if holding
"▲" or "▼" button). Time setting range is 0.5~ 24hours. Press this
button again to confirm timer setting and the characters of HOUR
ON (OFF) will stop flashing.
If the characters are flashing but you haven't press timer
button,timer setting status will be quit after 5s.If timer is confirmer,
press this button again to cancel timer.
button
Press this button in COOL or DRY mode to turn on X-fan function.
When this function is started up, indoor fan will still operate at low
fan speed for a while after turning off the unit by remote controller.
Technical Information
" signal, while it displays
" icon will
" will be
" will disappear.
button
Press this button to turn on the display's light and press this button
again to turn off the display's light.
Function introduction for combination buttons
Child lock function
Press "▲" and "▼" buttons simultaneously 3s to lock or unlock
the keypad. If the remote controller is locked, "
this case, pressing any button, "
Combination of "Mode" and "▼" buttons:
About switch between Fahrenheit and centigrade
At unit OFF, press "Mode" and "▼" buttons simultaneously to
switch between °C and °F.
Combination of "Temp" and "Timer" buttons:
About Energy-saving Function
Press "Temp" and "Timer" simultaneously in COOL mode to start
energy-saving function.
Nixie tube on the remote controller displays "SE". Repeat the
operation to quit the function.
Combination of "Temp" and "Timer" buttons:
About 8°C Heating Function
Press "Temp" and "Timer" simultaneously in HEAT mode to start
8°C Heating Function. Nixie tube on the remote controller displays
" " and a selected temperature of "8°C". (46°F if Fahrenheit is
adopted).
Repeat the operation to quit the function.
WiFi function
Press "Mode" and "Turbo" button simultaneously to turn on or turn
off WiFi function. When WiFi function is turned on, the "
will be displayed on remote controller; Long press "Mode" and
"Turbo" buttons simultaneously for 10s, remote controller will send
WiFi reset code and then the WiFi function will be turned on. WiFi
function is defaulted ON after energization of the remote controller.
NOTE:
● This function is only available for some models.
Auto clean function
U n d e r u n i t o ff s t a t u s , h o l d " M O D E " a n d " FA N " b u t t o n s
simultaneously for 5s to turn on or turn off the auto clean function.
When the auto clean function is turned on, indoor unit displays
"CL" . During the auto clean process of evaporator, the unit will
" is displayed. In
" blinks three times.
" icon
43