Working Instructions - Scheppach C-MT40-X Translation Of The Original Operating Instructions

8.4.2 Removing the tool attachment
1. Turn the lever (1) through 180° until it engages.
This lifts the union nut (8) and releases the tool at-
tachment receiver (7).
2. Removing tool attachments when the tool receiver is
open:
Remove the tool attachment from the tool attachment
receiver (7).
Loosen the union nut (8), using a slotted screwdriver
(not included in the scope of delivery) if required.
3. Remove tool attachments with closed tool receiver:
Dismantle the union nut (8) and remove the tool at-
tachment from the tool attachment receiver (7).
4. After inserting, use a slotted screwdriver (not included
in the scope of delivery) to re-tighten the union nut (8).
5. Turn the lever (1) 180° again until it clicks into place.
8.5 Adjusting the oscillation rate (fig.
8)
Note:
The required oscillation rate depends on the material and
the working conditions, and can be determined by a prac-
tical trial.
1. Use the speed control (5) to select the oscillation rate.
Level 1:
Level 6:
Note:
The oscillation rate can also be changed during operation.
8.6 Switching on/off (fig. 7, 9)
ATTENTION
Before use, check the inserted tool to ensure all fasten-
ing parts are attached correctly.
Note:
• Always hold the product tight with both hands
during work. Make sure that you have a secure foot-
ing.
• Do not machine material containing asbestos. As-
bestos is considered carcinogenic.
CAUTION
Keep your hands away from the tool attachment when
the product is in operation.
Switching on
1. Push the ON/OFF switch (2) into position I to switch
the product on.
Switching off
1. Push the ON/OFF switch (2) into position 0 to switch
off the product.
8.6.1 LED work lamp (9)
This product is equipped with an LED work lamp to illumi-
nate the immediate work area and improve visibility in
poorly lit environments.
22 | GB
Low oscillation rate
High oscillation rate
www.scheppach.com
CAUTION
Do not look directly into the LED work lamp or the light
source.
1. The LED work lamp (9) lights up automatically as
soon as the product is switched on.
Note:
The LED work lamp remains lit up for approx. 10 seconds
after the product is switched off.
8.7 Test run
Note:
Before the first work and after each tool attachment
change, carry out a test run without load. Switch off the
product immediately if the tool attachment runs out of
round, there is considerable vibration or abnormal noises
are heard.
9

Working instructions

• The oscillating drive causes the tool attachment to os-
cillate forwards and backwards 10000 to 40000 times
per minute. This enables precise work in narrow spac-
es.
• Ensure that the ventilation slots are not covered.
• Check whether you have selected the correct tool for
the intended use prior to starting operation.
• Switch on the product and only then approach the ma-
terial to be processed.
9.1 Sawing/cutting
• Only use undamaged saw blades that are in perfect
condition. Saw blades that are bent, blunt or damaged
in any other way can break.
• Do not exert excessive pressure on the product. Let
the product do the work.
• When sawing lightweight materials, observe the legal
regulations and the material manufacturer's recom-
mendations.
• Only soft materials such as softwood, plasterboard or
similar are permitted to be machined using the plunge
sawing procedure.
• When cutting wall tiles, note that the tool attachments
are subject to increased wear when used for an ex-
tended period.
9.2 Sanding
• Attaching sanding sheets:
Push the sanding sheets (17) onto the delta grinding
plate (13).
• Removing sanding sheets:
Pull the sanding sheets (17) off the edge of the delta
grinding plate (13) and dispose of them.
• Ensure that the contact pressure is even. Excessively
increasing the contact pressure does not lead to a
higher sanding rate, but to greater wear on the sand-
ing sheets.