Draper 55588 Instruction Manual
  1. Manuals
  2. Brands
  3. Draper Manuals
  4. Saw
  5. 55588
  6. Instruction manual

Draper 55588 Instruction Manual

Brushless sliding compound mitre saw
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
20V 185mm BRUSHLESS
SLIDING COMPOUND MITRE
SAW
55588
SCIE À ONGLET AVEC
F
TABLE COULISSANTE
SANS BALAI 20V 185mm
55588
SIERRA ELÉCTRICA
E
COMBINADA DESLIZABLE
ESCOBILLAS DE 20V 185mm
55588
MULTI-TOOL BATTERY SYSTEM
ORIGINAL LANGUAGE
SERRA ESQUADRIA COM
P
COMPOSIÇÃO DESLIZANTE
SEM ESCOVAS DE 20V 185mm
55588
D
BÜRSTENLOSER 20V 185mm
GEHRUNGSZUGSÄGE
55588
185mm 20V BORSTELLOZE
SCHUIFVERSTEKZAAG
55588

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 55588 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Draper 55588

Summary of Contents for Draper 55588

  • Page 1 MULTI-TOOL BATTERY SYSTEM  ORIGINAL LANGUAGE 20V 185mm BRUSHLESS SLIDING COMPOUND MITRE 55588 SCIE À ONGLET AVEC SERRA ESQUADRIA COM COMPOSIÇÃO DESLIZANTE TABLE COULISSANTE SEM ESCOVAS DE 20V 185mm SANS BALAI 20V 185mm 55588 55588 SIERRA ELÉCTRICA BÜRSTENLOSER 20V 185mm GEHRUNGSZUGSÄGE...

  • Page 2: Explanation Of Symbols

     INTRODUCTION Blade diameter. 1.1 SCOPE This machine is designed to cut wood; for example, Blades bore diameter. timber frames and roof frames, etc. As part of our core range, this product is intended for domestic and infrequent light trade use only. Any application other than that it was intended for, is Speed (no load).

  • Page 3: Specification

    Power tool plugs must match the outlet. 2.1 SPECIFICATION Never modify the plug in any way. Do not use any adapter plugs with earthed Stock No............... 55588 (grounded) power tools. Unmodified plugs Part No............D20MS185 and matching outlets will reduce risk of electric shock.
  • Page 4 switch or energising power tools that have the cutting edges are less likely to bind and are switch on invites accidents. easier to control. d) Remove any adjusting key or wrench g) Use the power tool, accessories and tool before turning the power tool on. A wrench bits etc.
  • Page 5 holes. Blades that do not match the mounting produce narrow kerf causing excessive hardware of the saw will run off-centre, friction, blade binding and kickback. causing loss of control. f) Blade depth and bevel adjusting locking h) Never use damaged or incorrect blade levers must be tight and secure before washers or bolt.

  • Page 6: Additional Safety Instructions For Laser Products

    – Do not expose to rain. wood or other similar rough-coated surfaces. Reflective metallic surfaces such as sheet steel, or – Only use Draper D20 battery packs with this product. similar, are not suitable as the laser beam guide Consult your Draper stockist for details.

  • Page 7: Unpacking And Checking

    Check contents against the parts shown in Fig A. If any part is damaged or missing, please contact the Draper Help Line (see back page). Do not attempt to use the product! The packaging material should be retained during the warranty period, in case the product needs to be returned for repair.
  • Page 8  IDENTIFICATION – FIG.A (13) (14) (28) (18) (20) (19) (24) (22) (15) (16) (11) (22) Fence. (1) Bevel pointer. Spindle lock button. Plunge handle. Table. (19) Lower blade guard. (12) (17) Laser guide. Table insert. (18) Mitre latch. Mitre pointer. (10) Saw head locking pin.

  • Page 9: Basic Operations

     position. When tight, this handle stops the table from BASIC OPERATIONS rotating. Note: Before making any cuts, make sure the handle is 6.1 TRANSPORTATION – FIG.1 tightened preventing any movement. The saw head is locked in the down position for transport purposes and should be returned to this position when not in use.
  • Page 10 6.7 CHECKING THE FENCE TO BLADE (19.1) ALIGNMENT – FIGS.7 – 8 Note: Isolate the power source by either removing the power supply plug from the socket, or battery from the tool, before carrying out adjustment, servicing or (19.2) maintenance. −...
  • Page 11 6.10 BEVEL ADJUSTMENT – FIG.11 It is possible to set the bevel angle from 0Ø to 45Ø. − Loosen lock (17) and adjust the bevel angle as indicated on scale (2). Tighten locking knob (17) to secure. (10) (17) FIG. 6.9 DEPTH OF CUT STOP –...
  • Page 12 6.13 SLIDING LOCK – FIG.15 Checking the 45Ø angle stop. For checking and adjustment of the 45Ø bevel angle: For most operations the sliding feature will be required − Loosen the bevel locking knob (17) and tilt the cutting to allow full capacity cutting, however it is possible to lock the sliding bars by tightening locking knob (16).
  • Page 13 6.15 BATTERY INSTALLATION/ REPLACEMENT FOR LASER GUIDE – FIGS. 17 – 18 Note: Isolate the power source by either removing the power supply plug from the socket, or battery from the tool, before carrying out adjustment, servicing or maintenance. (24) (23) Warning! Avoid direct eye contact with the laser.
  • Page 14 − Rotate the cover plate (12.2) to its original position (12.1) until the slot in the cover plate engages with the outer-most screw (12.1). − Rotate the cover plate (12.2) to its original position until the slot in the cover plate engages with the outer-most screw (12.1).
  • Page 15 (12.1) (14) (12.5) (12.5) (12.5) FIG. FIG. BASIC COMPOUND MITRE  SAW OPERATIONS Warning! Never connect the plug to a power source outlet until all the preliminary adjustment steps are complete and you have read and understood the safety and operational instructions. 7.1 USING THE LASER GUIDE –...
  • Page 16 located in the trigger switch enabling the insertion of a padlock or locking chain (supplied separately), to prevent children or unauthorised users from operating the saw. 7.3 BODY AND HAND POSITION Proper positioning of your body and hands when operating the mitre saw will make cutting easier and safer.

  • Page 17: Battery Charging

    To cut an inside corner: – FIGS. 33 – 34 − Cut the left side by aligning the top of the moulding 55588 is supplied “bare”, without battery pack or against the fence. charger. For compatible batteries, chargers and − Set the bevel to 33.9°...
  • Page 18 (the red LED will go from flashing to Allow battery/charger to normalise and try again. If a constant red. fault remains after trying this then contact Draper Tools. − When the battery is fully charged the green LED BATTERY PACK PROTECTION stops flashing and remains a constant green.

  • Page 19: Maintenance And Troubleshooting

    Warning! To avoid injury from unsafe accessories, Always unplug the power cable before any maintenance use only Draper accessories. check on this saw. 10.5 PROHIBITED ACCESSORIES Danger! Never put lubricants on the blade whilst it is spinning.

  • Page 20: Troubleshooting Guide

     WARRANTY 9.1 WARRANTY Draper power tools have been carefully tested & inspected and are guaranteed to be free from defective materials or workmanship. For details of warranty and terms and conditions please visit the Draper Tools website at www.drapertools.com/warranty...

  • Page 21: Battery Pack Disposal Information

     10. DISPOSAL 10.1 DISPOSAL – At the end of the machine’s working life, or when it can no longer be repaired, ensure that it is disposed of according to national regulations. – Contact your local authority for details of collection schemes in your area.

Table of Contents