Linergy CRISTAL Series Installation And Use Instruction

Linergy CRISTAL Series Installation And Use Instruction

Rest mode emergency luminaire

Advertisement

Quick Links

ISTRUZIONI PER L'INSTALLAZIONE E L'USO
I

INSTALLATION AND USE INSTRUCTIONS

UK
CARATTERISTICHE GENERALI:
- Led spia verde per presenza rete.
- Funzionamento con batterie ricaricabili al Ni-Cd e al NiMH.
- Dispositivo di ricarica delle batterie a corrente costante.
- Dispositivo di protezione contro la scarica eccessiva della batteria.
- Possibilità di messa in stato di riposo tramite il comando remoto
Commander (opzionale).
- Possibilità di applicare dei pittogrammi di segnalazione.
- Corpo in materiale plastico conforme alle normative vigenti.
Attenzione: In caso di installazione a parete il prodotto deve essere
disposto con i led verso il BASSO
BATTERIE:
Sostituire la batteria ogni quattro anni o quando l'autonomia non è
più quella nominale. C'è uno spazio da riempire a cura
dell'installatore con la data di entrata in funzione.
Attenzione: Le batterie al Ni-Cd e Ni-MH sono inizialmente
scariche, la prima ricarica deve durare almeno 48h.
INSTALLAZIONE: (FIG.2)
-Rimuovere il diffusore trasparente 1 facendo leva con
dei cacciaviti nei punti 2.
-Sganciare il riflettore 3 dalla base 4 facendo leva con un cacciavite
nel punto 5.
-Forare se necessario uno dei tre possibili ingressi laterali per il cavo
di alimentazione ed applicare
la base 4 al muro tramite gli appositi fori per il fissaggio.
-Eseguire i cablaggi come esposto in fig.3,4,5,6
-Riagganciare il riflettore 3 alla base 4 facendo scattare il denti nel
punto 5.
-Riagganciare il diffusore trasparente 1 alla base 4 facendo scattare i
denti nei punti 2.
CARATTERISTICHE TECNICHE/TECHNICAL CHARACTERISTICS
ALIMENTAZIONE/ POWER SUPPLY
POTENZA ASSORBITA/ POWER ABSORPTION
GRADO DI PROTEZIONE/ PROTECTION DEGREE
CLASSE DI ISOLAMENTO/ INSULATING CLASS
SEZIONE DEL CAVO/ WIRE DIAMETER
N.B.
inserire i tappi in dotazione negli appositi spazi laddove
viene inserito il tassello per l'installazione, al fine di per
garantire la tenuta stagna dell'apparecchio.
Fig.2b
CRISTAL
REST MODE
APPARECCHIO DI EMERGENZA
EMERGENCY LUMINAIRE
MADE IN ITALY
230Vac - 50Hz
6VA
IP 40-IP65
II
2
0,5 ÷ 5mm
N.B.
In order to ensure the watertight integrity
of the fitting insert the covers coming with the product
in the reserved places where the screws anchors are
inserted.
INSERIRE IL RACCORDO
IN DOTAZIONE PER GARANTIRE
LA TENUTA STAGNA.
INSERT THE IP65 CONNECTOR
SUPPLIED TO ENSURE THE WATER-
TIGHT INTEGRITY OF THE FITTING.
EN 60598-1
EN 60598-2-22
Compliant
2002/95/CE RoHS

GENERAL CHARACTERISTICS:

- Indicator green Led for the presence of the power supply.
- Operation with rechargeable Ni-Cd and NiMH batteries.
- Constant current electronic device for the charge of the battery.
- Electrical protection device for the excessive discharge of battery.
- Possibility to be put in the stand-by mode by remote control
Commander (optional)
- Possibility to put a green signal label .
- Plastic body in accordance with the rules in force.
Warning: In case of wall mounting the product must be positioned
with the leds down.
BATTERIES:
It is recommended to substitute each battery every four years or when
the nominal autonomy is not guaranteed. The model and the date of
production of the battery are written on it. Fill the field with the date of
the first starting (Fig.1).
Warning: The Ni-Cd and Ni-MH batteries are sold uncharged: the
first charge must be 48h long.

INSTALLATION: (FIG.2)

-Remove the transparent cover 1 pushing with a screwdriver
in the points 2.
-Unhook the body of the lamp 3 from the base 4 with a screwdriver in
the point 5.
-Drill in necessary one of the three possible entries for the power
supply cable and fix the base 4 to the wall using the holes on the
base.
-Make the connections as shown on fig.3,4,5,6.
-Hook the body 3 to the base 4 making release the tooth on point 5.
-Hook the transparent cover 1 to the base 4 making release the tooth
on points 2.
5
3
Fig.2
IP40-IP65
230 Vac - 50 Hz
03
4
5
2
2
2
1
2

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CRISTAL Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Linergy CRISTAL Series

  • Page 1 CRISTAL REST MODE APPARECCHIO DI EMERGENZA EMERGENCY LUMINAIRE MADE IN ITALY IP40-IP65 230 Vac - 50 Hz ISTRUZIONI PER L'INSTALLAZIONE E L'USO EN 60598-1 EN 60598-2-22 Compliant 2002/95/CE RoHS INSTALLATION AND USE INSTRUCTIONS CARATTERISTICHE GENERALI: GENERAL CHARACTERISTICS: - Indicator green Led for the presence of the power supply. - Led spia verde per presenza rete.
  • Page 2 INSTALLAZIONE STANDARD - INIBIZIONE STANDARD INSTALLATION - INHIBITION - NON PERMANENTE SE / NON MAINTAINED NON PERMANENTE NOT MAINTAINED 230Vac - 50Hz N.B. Mai collegare la tensione di rete sui morsetti INTERRUTTORE A-B, la scheda elettronica si danneggia. ESTERNO A-B Interruttore di inibizione, chiuderlo con un ponte EXTERNAL a filo per abilitare l’emergenza.
  • Page 3 CONFIGURAZIONE DEL PRODOTTO PER L’UTILIZZO DEL COMMANDER: HOW TO CONFIGURE THE PRODUCT FOR THE USE WITH COMMANDER: Presenza Abilitazione RETE Emergenza COMMANDER SPOSTARE IL JUMPER J7 PER LA CONFIGURAZIONE REST MODE - COMMANDER MOVE THE J7 JUMPER AS SHOWN IN THE PICTURE «REST MODE COMMANDER»”...
  • Page 4 The warranty on the emergency luminaire is 2 years from the sales date. The warranty voids if the product has been mishandled or repaired by personnel not authorized by LINERGY. LINERGY S.R.L. - via A. De Gasperi 9 - Acquaviva Picena (AP) - ITALY - tel.0735.5974 - fax 0735.597474 - www.linergy.it - info@linergy.it - ISTCR-RM Ver. 3.1...

This manual is also suitable for:

Cr08n10egrCs08n10egrCr11n30egrCs11n30egrCr08n30agrCs08n30agr ... Show all

Table of Contents