Product Details - Bose PowerShareX PSX1204D Installation Manual

Product Details

PowerShareX PSX1204D/PSX2404D/PSX4804D
Front Panel (cover removed)
Access the front panel by removing the left faceplate and protective mesh. The faceplate is secured by magnets.
q w e r
ON
SDBY
CALL
PWR
CH1 CH2 CH3 CH4
q
Service port: For service only.
w
Power button: To switch between system On and Standby mode, press and hold for
three seconds. If desired, the operating condition can be modified by the
GPI/Remote (Remote On/Off).
e
Operating Mode LEDs: The LED will light green to indicate whether the amplifier is
On or in Standby mode.
LED Light Color & Pattern
ON Off
ON Solid green
SBY Off
SBY Solid orange
SBY Blinking orange
Blink "counter"
SBY
(pattern of blinks)
r
Callback button: Reserved for future use.
t
Soft Reset button: Resets network parameters to default settings (DHCP). Press
and hold for three seconds.
y
Hard Reset button: Restarts amplifier. Settings and loudspeaker EQs/presets are
unaffected. Can be used to cycle power when rear panel is inaccessible. Press and
hold for three seconds.
Note: To reset the amplifier to factory settings (DHCP), press and hold both the
Soft Reset and Hard Reset buttons for three seconds. This removes loudspeaker EQs/
presets and resets any adjusted settings.
u
Self Check button: For service only.
i
Channel Attenuation controls: Attenuation controls for the output level of each
channel. Turn the controls clockwise to decrease attenuation and counter-
clockwise to increase attenuation. Output level can also be adjusted with
ControlSpace Designer.
Note: The attenuation control is in series with the Remote Level connector to limit the
output volume regardless of any remote adjustment.
4 • English
t y u i o
CLIP
-6dB/TEMP
SOFT HARD -12dB
CHECK
RESET RESET
-24dB
SIGNAL
READY
ALARM
Indication
Amplifier is powered off
Amplifier is powered on
Amplifier is powered on
Amplifier is in standby mode
Amplifier is in auto-standby mode
Error code; contact Bose Professional
technical support
a
LIMIT
TEMP
CHECK
REMOTE
POWER ON
MAINS
ALARM
o
Channel Status LEDs: Status LED signal metering for Channels 1, 2, 3, and 4. See the
table below for details.
LED Name Light Color & Pattern
CLIP Orange
–6dB/TEMP Solid yellow
Steady flashing
–6dB/TEMP
yellow
–12dB Green
–24dB Green
SIGNAL Solid green
SIGNAL Blinking green
READY Solid green
ALARM Solid red
a
System Status LEDs: System status indicators. See the table below for details.
LED Name Light Color & Pattern
LIMIT Pulse flashing orange
LIMIT Solid orange
TEMP Solid yellow
CHECK Solid orange
CHECK Blinking orange
CHECK Fast-blinking orange
REMOTE Solid green
REMOTE Off
POWER ON Solid green
POWER ON Off
MAINS Solid green
MAINS Off
MAINS Pulse-flashing green
MAINS Fast-blinking green
MAINS Blinking green
ALARM Solid red
Notes:
1. Timing patterns of System Status and Channel Status LEDs:
Lighting Timings
100 ms on
Pulse flashing
400 ms off
100 ms on
Steady flashing
900 ms off
100 ms on
Fast blinking
100 ms off
500 ms on
Blinking
500 ms off
PowerShareX PSX1204D/PSX2404D/PSX4804D • Installation Guide
PRO.BOSE.COM
PSX1204D
Signal
Other Indication
1
Metering
Clipping —
Thermal warning; thermal
–6 dB
is protection engaged
–6 dB Auto-standby
–12 dB —
–24 dB —
–60 dB Signal presence
–60 dB Channel is muted
— Channel is ready
— Channel fault
Indication
1
Breaker Save is enabled
Breaker Save is limiting power
draw
Thermal warning; thermal is
protection engaged
System is self-checking
Self-check is complete
Self-check is unavailable
Reserved for future use
—
System is ready
System is off
AC mains voltage is within
operating range
Under-voltage
Over-/under-voltage warning
Over-voltage
Blown mains fuses
PSU fault or critical faults
Behavior