Advertisement
Quick Links
Advertisement
Related Manuals for Planet Networking & Communication WBS-512AC
Summary of Contents for Planet Networking & Communication WBS-512AC
- Page 1 802.11ac 900Mbps Outdoor Wireless CPE WBS-512AC Quick Installation Guide...
-
Page 2: Table Of Contents
Table of Contents 1. Package Contents ................. 3 2. Physical Introduction ................4 3. Hardware Installation ................5 4. Wired Network Configuration (Windows 10 and Windows 11) ....6 5. Entering into the Web Management ............7 6. Easy to Set Up PtP Connection .............. 8 7. -
Page 3: Package Contents
1. Package Contents Thank you for choosing PLANET Outdoor Wireless CPE. Before installing, please verify the contents inside the package box. WBS-512AC Quick Guide Sheet Let’s get started with your PLANET product WBS-512AC Please scan the QR code to browse our online User’s Manual or Quick Installation Guide and follow the instructions to complete the setup. -
Page 4: Physical Introduction
2. Physical Introduction Hardware Description PtP Switch DC Power Reset/Pair LED Indicators... -
Page 5: Hardware Installation
3. Hardware Installation Step 1: Push the latch on the bottom of the Outdoor Wireless CPE to remove the sliding cover. Step 2: Plug the RJ45 Ethernet cable into the PoE Port of the Outdoor Wireless CPE. Then, slide back the cover to finish the installation. Step 3: Place the mounting strap through the slot on the back of the Outdoor Wireless CPE and then around the pole. -
Page 6: Wired Network Configuration (Windows 10 And Windows 11)
4. Wired Network Configuration (Windows 10 and Windows 11) A computer with wired Ethernet connection is required for the first-time configuration of the Wireless AP. 1. Click the “Start” button located at the lower-left corner of your computer. 2. Select “Control Panel-> Network and Sharing Center”. 3. Click “Change adapter settings”. 4. -
Page 7: Entering Into The Web Management
5. Entering into the Web Management Default IP Address: 192.168.1.253 Default Password: admin Default SSID (5GHz): PLANET_5G Step 1: Launch browser enter default address http://192.168.1.253. Step 2: The default password is “admin”. Then click the LOGIN button to continue. For security reasons, it is recommended to change the password at the first login and memorize it. -
Page 8: Easy To Set Up Ptp Connection
6. Easy to Set Up PtP Connection Step 1: (1) Position "Master" to "Slave" on the AP. (2) Press the "Reset/Pair" button on both APs to be connected in 2 minutes. (3) The connection has been successfully established. 3 Steps to Set Up PtP Connection PtP Mode Connecting Slave... -
Page 9: Ap Discovery Through Planet Nms Controller (Nms-500/Nms-1000V)
7. AP Discovery through PLANET NMS Controller (NMS-500/NMS-1000V) The WBS-512AC is the Smart AP series which can be centrally managed by PLANET NMS Controller. Follow the steps below to discover the managed AP through PLANET NMS controller (NMS-500/NMS-1000V). Please ensure each managed AP uses a different static IP in the same subnet before physically connecting to the managed network. - Page 10 Step 2: Go to the “Domain” page to discover and add the managed AP to the device list. Then, you can go to the “AP Control-> AP Management” page to configure pre-defined profiles to the managed AP without logging on to the AP’s web page. ...
-
Page 11: Further Information
Further Information: The above steps introduce the simple installations and configurations of the device. For further configurations, please refer to the user manual, which can be downloaded from the website. WBS-512AC: https://www.planet.com.tw/en/support/downloads?&method=keyword&keyword =WBS-512AC&view=3#list PLANET Network Management Solution (NMS): https://www.planet.com.tw/en/products/network-management If you have further questions, please contact the local dealer or distributor...