Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for ADJ FL1300
Summary of Contents for ADJ FL1300
- Page 1 ENCORE BURST 200 User Guide...
- Page 2 Products, LLC brands and product names are trademarks or registered trademarks of their respective companies. ADJ Products, LLC and all affiliated companies hereby disclaim any and all liabilities for property, equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic...
-
Page 3: Table Of Contents
C O N T E N T S General Information Limited Warranty (USA Only) Safety Guidelines Maintenance Guidelines Fixture Overview Installation Instructions System Menu Dimming Curve DMX Channel Functions and Values Specifications | FCC Statement Dimensional Drawings... -
Page 4: General Information
Please do NOT discard the outer shipping carton in the trash. Please recycle whenever possible. CUSTOMER SUPPORT: Contact ADJ Service for any product related service and support needs. Also forums.adj.com visit with questions, comments or suggestions. -
Page 5: Limited Warranty (Usa Only)
ADJ Products, LLC concludes, after inspection, affects the reliability of the product; if the product has been repaired or serviced by anyone other than the ADJ Products, LLC factory unless prior written authorization was issued to purchaser by ADJ Products, LLC; if the product is damaged because not properly maintained as set forth in the instruction manual. -
Page 6: Safety Guidelines
This fixture is a sophisticated piece of electronic equipment. To guarantee smooth operation, it is important to follow all instructions and guidelines in this manual. ADJ is not responsible for injury and/ or damages resulting from the misuse of this fixture due to the disregard of the information printed in this manual. - Page 7 S A F E T Y G U I D E L I N E S • DO NOT TOUCH the fixture housing during operation. • Turn OFF the power and allow approximately 15 minutes for the fixture to cool down before serving.
-
Page 8: Maintenance Guidelines
M A I N T E N A N C E G U I D E L I N E S DISCONNECT POWER BEFORE PERFORMING ANY MAINTENANCE! CLEANING Frequent cleaning is recommended to insure proper function, optimized light output, and an extended life. -
Page 9: Fixture Overview
O V E R V I E W Interlocking Pin Integrated Mounting Bracket Yoke Bracket Mounting Hole Positional Lenses Aperture to loosen tighten key for Positional Lens Screws 3-Pin DMX Control LCD Display In/Out Menu Safety Cable Power Cable In/Out Attachment INCLUDED ITEMS •... -
Page 10: Installation Instructions
I N S TA L L AT I O N I N S T R U C T I O N S IPX4 RATED An IP rated lighting fixture is commonly installed in outdoor environments and has been designed with an enclosure that effectively protects the ingress (entry) of external foreign objects such as dust and water. - Page 11 I N S TA L L AT I O N I N S T R U C T I O N S DO NOT INSTALL THE FIXTURE IF YOU ARE NOT QUALIFIED TO DO SO! Fixture MUST be installed following all local, national, and country commercial electrical and con- struction codes and regulations.
- Page 12 I N S TA L L AT I O N I N S T R U C T I O N S OVERHEAD RIGGING Overhead rigging requires extensive experience, including calculating working load limits, installation material being used, and periodic safety inspection of all installation material and the fixture, among other skills.
- Page 13 I N S TA L L AT I O N I N S T R U C T I O N S YOKE BRACKET KIT The included Yoke Bracket Kit can be attached to the fixture using the included hardware. Follow the installation steps below.
- Page 14 I N S TA L L AT I O N I N S T R U C T I O N S CONNECTING FIXTURES The fixture includes a unique interlocking system which allows multiple fixtures to be connected together horizontally, using the 4 included spring-loaded interlocking pins on each fixture. Follow the installation steps below.
- Page 15 I N S TA L L AT I O N I N S T R U C T I O N S MAXIMUM NUMBER OF CONNECTING FIXTURES = 10 Each set of 10 fixtures must be attached to a structure which can support 10x the total weight of the entire assembly (10 x combined weight of 10 fixtures and any associated hardware and accessories).
- Page 16 I N S TA L L AT I O N I N S T R U C T I O N S SAFETY CABLES Each fixture includes a Safety Cable attachment loop on the back. All fixtures installed in an overhead configuration MUST always be secured with a dedicated secondary safety attachment, such as an appropriately rated safety cable that can hold 10 times the weight of the fixture.
- Page 17 I N S TA L L AT I O N I N S T R U C T I O N S ADJUSTING LED LENS POSITION DEGREE The LED lens position can easily be adjusted manually from the default 0-degree position, to 7.5+ or 15+ degrees (UP) and -7.5 and -15.0 degrees (DOWN).
-
Page 18: System Menu
S Y S T E M M E N U The fixture includes an easy to navigate system menu where fixture settings can be adjusted via the LCD control panel located on the back of the fixture. (see image below) To access the system menu press and hold the MENU button for 3 seconds. - Page 19 S Y S T E M M E N U Addr: DMX-512 Address Setting. Select “Addr,” then press the ENTER button. When the display begins to blink, use the DOWN and UP buttons to change the DMX-512 address (001-512). Once the address has been selected, press the ENTER button to confirm, or press the MENU button to exit without making any change.
- Page 20 S Y S T E M M E N U FAeq: Dimming Frequency. Select “FAeq,” then press the ENTER button. Use the DOWN and UP buttons to scroll through the available frequency settings (900 Hz, 1000 Hz, 1100 Hz, 1200 Hz, 1300 Hz, 1400 Hz, 1500 Hz, 2500 Hz, 4000 Hz, 5000 Hz, 10000 Hz, 15000 Hz, 20000 Hz, or 25000 Hz).
-
Page 21: Dimming Curve
D I M M I N G C U R V E The fixture includes 6 different dimming curve modes which can selected from either the system menu or via DMX. The graph below provides details on each dimming curve mode. DIMMER 100% Time (ms) -
Page 22: Dmx Channel Functions And Values
D M X C H A N N E L F U N C T I O N S A N D V A L U E S CHANNEL FUNCTION VALUE 1CH 2CH 2ACH 3CH 4CH 6CH Master Dimmer - Left & Right Pixels, 0-100% 000 - 255 Dimmer Fine - Left &... -
Page 23: Specifications | Fcc Statement
S P E C I F I C AT I O N S Light Source: 2x 110W Warm White CREE COB (Chip On Board) LEDs 2,700K Color Temperature (1,200K Tungsten Mode) 50-degree Beam Angle CRI: 81 12249 LUX @ 1M; 490 LUX @ 5M 50,000 Hour Average LED Life Features: Modular design to connect multiple fixtures together in a vertical or horizontal tray from a built-in rail... -
Page 24: Dimensional Drawings
D I M E N S I O N D R A W I N G S Dimensions not to scale 15.7in. [400.0mm] 7.9in. [200.0mm]... - Page 25 D I M E N S I O N D R A W I N G S Dimensions not to scale 19.8in. [503.0mm] 17.4in. [443.0mm] 8.4in. [214.0mm] 7.8in. [197.7mm] 7.8in. [197.7mm] 8.2in. [207.7mm] 8.2in. [207.7mm]...