Subscribe to Our Youtube Channel
Related Manuals for Evolution F255 SMS
Summary of Contents for Evolution F255 SMS
- Page 1 F255 Original Instructions Instructions Originales Original Bedienungsanleitung Origineel Instructies GB2438285 Original written in UK English Date Published: 06/08/2018...
-
Page 2: Table Of Contents
Compound Cutting Assembly Diagrams Crown Moulding Cutting Saw Set Up Diagrams Cutting Bowed Material Saw Usage Diagrams Clearing Jammed Material Optional Evolution Accessories Assembly & Preparation Tools Needed Maintenance Environmental Protection Unlatching & Raising The Cutting Head Assembly Safety Checks... -
Page 3: Introduction
WEB: www.evolutionpowertools.com EMAIL: customer.services@evolutionpowertools.com WARRANTY Congratulations on your purchase (1.4) of an Evolution Power Tools Machine. Please complete your product registration ‘online’ as explained on the leaflet included with this machine. This will enable you to validate your machine’s warranty period via Evolution’s website by entering your details and thus ensure prompt service if ever needed. -
Page 4: Machine Specifications
www.evolutionpowertools.com MACHINE SPECIFICATIONS IMPERIAL MACHINE METRIC Motor (220-240V ~ 50 Hz) 1600W Speed No Load 2500 min 2500 rpm Weight (Net) 15.3kg 33.7lb Dust Port Diameter 35mm 1 -3/8 In. Tool Dimensions (H x W x L) (0° / 0°) 14- 3/16 x 27-3/4 360 x 705 x 730mm x 28-47/64 In. -
Page 5: Safety Labels & Symbols
Contact Evolution sliding mitre saw and has been designed Power Tools for replacement labels. to be used with genuine Evolution blades rated for this machine. Only use blades Note: All or some of the following symbols designed for use in this machine and/ may appear in the manual or on the product. -
Page 6: Safety Precautions
www.evolutionpowertools.com SAFETY PRECAUTIONS SAVE ALL WARNINGS & ELECTRICAL SAFETY INSTRUCTIONS FOR FUTURE (1.14) REFERENCE This machine is fitted with the correct moulded plug and mains lead for the designated market. The term “power tool” in the warnings refers to If the supply cord is damaged, it must be your mains-operated (corded) power tool or replaced by a special cord or assembly available battery-operated (cordless) power tool. -
Page 7: Specific Safety Instructions
www.evolutionpowertools.com 3) General Power Tool Safety Warnings b) Do not use the power tool if the switch does (2.4) [Personal Safety]. not turn it on or off. Any power tool that cannot a) Stay alert, watch what you are doing and use be controlled with the switch is dangerous and must common sense when operating a power tool. - Page 8 www.evolutionpowertools.com a) Mitre saws are intended to cut wood or with the outside bowed face toward the fence. wood-like products, they cannot be used Always make certain that there is no gap with abrasive cut-off wheels for cutting between the workpiece, fence and table along ferrous material such as bars, rods, studs, the line of the cut.
-
Page 9: Blade Safety
EN 847-1. practicable. It is not advisable to wear gloves • Only use genuine Evolution blades rated for when operating the mitre saw. this machine. • Do not use saw blades that are damaged or... -
Page 10: Safe Operation
www.evolutionpowertools.com PERFORM CUTS SAFE OPERATION (3.8) (3.7) CORRECTLY & SAFELY Always ensure that you have selected the correct Wherever practicable always secure the saw blade for the material being cut. Do not use work-piece to the saw table using the work this mitre saw to cut materials other than those clamp where provided. -
Page 11: Getting Started Unpacking
• Lock the cutting head in its lowest position. For instructions on how to identify the batch Ensure that the cutting head locking pin is code, please contact the Evolution Power completely engaged in its socket. Tools helpline or go to: www.evolutionpowertools.com... -
Page 12: Additional Accessories
ADDITIONAL ACCESSORIES (4.3) In addition to the standard items supplied with this machine the following accessories are also available from the Evolution online shop at www.evolutionpowertools.com or from your local retailer. (4.4) Description Part No FURY Multi-Materal FURYBLADE255MULTI TCT Blade... -
Page 13: Items Supplied
www.evolutionpowertools.com ITEMS SUPPLIED 4.2) F255SMS R255SMS+ 052-0001A 052-0006 052-0002A Product Code 052-0008 052-0003A 052-0011 Machine Table Extensions Double Ended Hex Key (M6 & M5) Rotary Table And Neck Cutting Head Carriage Slides Mitre Locking Knob Mains Cable Guide/Clamp Self Tapping Cap Screw Socket Headed Screws Cable Clamp Component Laser Lens Cap... -
Page 14: Machine Overview
www.evolutionpowertools.com MACHINE OVERVIEW Pictured: F255SMS (See * for R255SMS+ Parts) 1. CUTTING HANDLE 14. BLADE 2. BLADE GUARD LOCKING TRIGGER 15. LOWER BLADE GUARD 3. DUST BAG* 16. TABLE TOP 4. SLIDE LOCKING SCREW 17. ROTARY TABLE 5. DEPTH GAUGE 18. - Page 15 www.evolutionpowertools.com Pictured: F255SMS 26. ON / OFF TRIGGER SWITCH 37. CABLE GRIP COMPONENT (FITTED TO THE CABLE GUIDE CLAMP) 27. LASER GUIDE ON / OFF SWITCH 38. ANTI-VIBRATION SPRING 28. DUST EXTRACTION PORT (FITTED TO ITEM ‘4’ - THE SLIDE LOCKING 29.
-
Page 16: Assembly Diagrams
www.evolutionpowertools.com F255SMS Handle R255SMS+ Handle Fig. 1 Fig. 2 Fig. 3 Fig. 4 Fig. 5 Fig. 6 Fig. 7 Fig. 8 Fig. 9 Fig. 10 Fig. 11 Fig. 12... - Page 17 www.evolutionpowertools.com CLICK Fig. 13a Fig. 13b Fig. 14a Fig. 14b Fig. 14c Fig. 15 Fig. 16 Fig. 17 Fig. 18 Fig. 19 Fig. 20...
-
Page 18: Saw Set Up Diagrams
www.evolutionpowertools.com Fig. 21 Fig. 22 Fig. 23 Fig. 24 Fig. 25 Fig. 26 Fig. 27 Fig. 28a Fig. 28b Fig. 28c Fig. 29 Fig. 30... - Page 19 www.evolutionpowertools.com FIT LONG FIT LONG CLAMP CLAMP (R255SMS+) (R255SMS+) Fig. 31 Fig. 32 Fig. 33 Fig. 34 Fig. 35 Fig. 36 Fig. 39 Fig. 37 Fig. 38 Fig. 40 Fig. 41a Fig. 41b...
-
Page 20: Saw Usage Diagrams
www.evolutionpowertools.com 1) Hex headed bolt 2) Spring washer 3) Flat washer 4) Mitre saw base 5) Workbench 6) Flat washer 7) Spring washer 8) Hex nut 9) Lock nut Fig. 42 Fig. 43 F255SMS R255SMS+ 2pc Clamp 3pc Clamp Fig. 45 Fig. - Page 21 www.evolutionpowertools.com Fig. 53 Fig. 54 Fig. 55 Fig. 57 Fig. 58 Fig. 56 Fig. 60 Fig. 61 Fig. 59 Fig. 62 Fig. 63 Fig. 64...
-
Page 22: Assembly & Preparation
www.evolutionpowertools.com ASSEMBLY AND PREPARATION WARNING: Do not under any circumstances (7.1) plug the cutting head into the power supply WARNING: Always disconnect the saw and try to use it as a hand held circular saw. from the power source before making any adjustments. - Page 23 TO FIT THE TABLE EXTENSIONS: The carriage slide should be inserted from the back ensuring that the ‘Evolution’ logo is the correct way • Carefully examine the table extension pieces to up. (Fig. 9) determine which is for the right hand side and •...
-
Page 24: Unlatching & Raising
Raise and lower the cutting head several times WARNING: Only use genuine Evolution and also operate the sliding carriage. Check blades or those blades specifically that the cable does not become entangled with any other parts of the machine. -
Page 25: Checking & Adjusting
www.evolutionpowertools.com Install the new blade. Make sure the rotation If the blade is blade is not at 90 degrees arrow on the blade matches the clockwise (square) with the rotary table, then rotation arrow on the upper guard. adjustment maybe required. •... -
Page 26: Machine Fence Alignment
www.evolutionpowertools.com MACHINE FENCE ALIGNMENT To use the depth stop: The Fence must be aligned at 90˚ (square) to • Deploy the depth stop ‘stop plate’ a correctly installed blade. The Rotary table (Fig. 28a) by rotating it forward from its must be set at ‘0˚’... -
Page 27: The Laser
• Switch on the laser beam. • Repairs to the laser module must only be • Position the work-piece on the rotary table conducted by Evolution Power Tools or their and against the fence. authorized agent. • Slide the work-piece into position until... -
Page 28: Laser Adjustment
Note: This machine can be attached to the • Loosen the clamping screw. (Fig.41a) Evolution Mitre Saw Stand. (Fig. 44). This will • Carefully rotate the laser module, until the line provide a safe secure, and extremely portable is parallel with the marks in the cardboard. -
Page 29: For Portable Use
www.evolutionpowertools.com FOR PORTABLE USE: OPERATING INSTRUCTIONS • Mount the saw on a 18mm thick piece of Caution: All mitre saws should be inspected plywood or MDF (800mm x 500mm min size (particularly for the correct functioning of the recommended) using appropriate fastenings safety guards) before each use. -
Page 30: Preparing To Make A Cut
www.evolutionpowertools.com Place the saw on a secure stationary work • Lower the Cutting Handle downwards and surface and check the saw over carefully. cut through the work-piece. Check particularly the operation of all the • Allow the speed of the blade to do the work, machines safety features before attempting there is no need to apply undue pressure to to operate the machine. -
Page 31: Mitre Cutting
www.evolutionpowertools.com completely covering the blade teeth, and the The cutting head can be tilted from the normal 0˚ cutting head locked in the upper position, (perpendicular position) to a maximum angle of before releasing the Cutting Handle. 45˚ from the perpendicular to the left hand side WARNING: Never pull the cutting head and only. -
Page 32: Crown Moulding Cutting
CROWN MOULDING CUTTING OPTIONAL EVOLUTION ACCESSORIES This machine is capable of cutting the mitre angles required for Crown Mouldings. DUST BAG (Supplied with R255SMS+) To configure the machine to cut Crown A Dust Bag can be fitted to the extraction port Moulding: at the rear of the machine. -
Page 33: Maintenance
www.evolutionpowertools.com MAINTENANCE Note: Any maintenance must be carried out with the machine switched off and disconnected from the mains/battery power supply. Check that all safety features and guards operating correctly on a regular basis. Only use this machine if all guards/safety features are fully operational. -
Page 34: Assembly Safety Checks
www.evolutionpowertools.com ASSEMBLY SAFETY CHECKS PART CONDITION Slides Inserted through the bevel neck and connected to the cutting head. Locating lugs successfully deployed. Mitre Handle Locking Knob Installed into mitre handle / rotary table. Slide Carriage Inserted into the threaded hole in the bevel neck. Anti-vibration locking screw spring fitted beneath the locking screw hand knob. -
Page 35: Ec Declaration Of Conformity
EC DECLARATION OF CONFORMITY The manufacturer of the product covered by this Declaration is: Evolution Power Tools, Venture One, Longacre Close, Holbrook Industrial Estate, Sheffield, S20 3FR. The manufacturer hereby declares that the machine as detailed in this declaration fulfils all the relevant provisions of the Machinery Directive and other appropriate directives as detailed below. - Page 36 Schifterschnitt Im Lieferumfang enthalten Deckenschnitt Maschinenübersicht Schneiden von bogenförmigen Material 66 Montagediagramme Beseitigung von gestautem Material Sägeneinstellungsübersicht Optionales Evolution Zubehör Abbildungen zum Gebrauch der Sägen Wartung Montage & Vorbereitung Umweltschutz Benötigte Werkzeuge Sicherheitskontrollen Entriegeln & Anheben des während der Montage Schneidekopfs Abschließende sicherheitstechnische...
Need help?
Do you have a question about the F255 SMS and is the answer not in the manual?
Questions and answers