Operation - EINHELL CE-CB 18/254 Li Original Operating Instructions

To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
5.2 Battery capacity indicator (Fig. 5)
Press the switch for the battery capacity indicator.
The battery capacity indicator shows the charge
status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.
5.3 Installing the battery (Fig. 6-7)
Push the battery into the battery mount provided.
When the battery is positioned as in Fig. 7, make
sure that the pushlock button latches in place!
To remove the battery, press the pushlock button
and take out the battery (Fig. 8).
Anl_CE_CB_18_254 Li_SPK7_THA.indb 15 Anl_CE_CB_18_254 Li_SPK7_THA.indb 15
EN

6. Operation

Warning!
Always remove the battery pack before making
adjustments to the equipment.
Please refer to the table in section 12 for the char-
ging time.
6.1 Mounting the polishing bonnet on the po-
lishing disk (Fig. 9)
1. Turn the car polishing machine upside down
so that the polishing disk is facing up.
2. Pull the textile polishing bonnet over the poli-
shing disk. Make sure that the textile polishing
bonnet is free of any foreign bodies.
6.2 Applying wax/polishing paste to the texti-
le polishing bonnet (Fig. 10)
Note: Use only high-quality waxing and polishing
products and follow the processing instructions
issued by the manufacturer on the packaging.
Distribute the polishing agent evenly as far as the
edge of the textile polishing bonnet so that a uni-
form, thin coating is produced overall.
Note: Applying too much polishing agent will only
make it more diffi cult to remove the layer of poli-
shing agent later from the paintwork and will not
improve the results.
6.3 Switching on and applying the polishing
agent to the paintwork
Note: The paintwork you want to process must be
carefully cleaned and completely dry. Severely
oxidized paintwork requires the use of a special
cleaner.
Select a cleaner from the products available to
suit the state of the paintwork and the stress it is
exposed to.
1. Dab with the textile polishing bonnet on dif-
ferent positions of the paintwork you want to
polish. This will help to distribute any excess
polishing agent over the textile polishing
bonnet and/or over the paintwork you want to
polish.
2. Hold the handle of the equipment fi rmly in
both hands, place the polishing machine onto
the paintwork you want to polish (Fig. 11) and
switch on the equipment by pressing the On/
Off switch (Fig. 1 / Item 3).
3. First work on the large level surfaces such
as the engine hood, boot lid and roof (Fig.
12), then on the smaller surfaces such as the
doors and mudguards (Fig. 13). Guide the
- 15 -
07.07.2023 09:40:36 07.07.2023 09:40:36