Advertisement
Openin
g
and
c
losing
-
Depending on the model of the system, you
may need to release the button on the
re-
mote contro
l
during programm ing and
press it again. Hold each posit ion you try for
at least 15 seconds before trying another
position
.
Keep the t urn signals
on
your
vehi-
cle in view when do ing t
his.
-
After programmi ng the garage door opener,
it may be necessary to synchronize the mo-
tor w ith the system
.
Refer
to the manufac-
ture r's instructions
.
Programming the buttons (version
B)
Applies
to
vehicles:
with garage door opener (Homelink)
Fig. 3
4
Distance betwee
n
t he
radiat
or
grille
and
the hand
tra nsmitt
er
Programming the button
:
Part
1
with the
contr
ols
1. Switch the ignition on
.
2.
Press and hold bot
h
outer buttons in the roof
headliner
¢
page
39,
fig.
33 until t he
LED@
turns off complete ly (after about 20 sec-
onds)
.
This procedure clears the sta ndard co-
des that were
set
at the factory and does
not
need to be repeated
again
to prog ram
t he
ot
her
butto
ns.
3.
Brief
ly press the butto
n
on the roof
headli
ner
that yo
u
wou ld like to program.
4.
Wait
unti
l
the
LED@
begins to
bli
nk quickly.
Programming mode is active for 5 minutes
.
5.
Move in front of your vehicle while holding
the original remote contro
l
for the system
that would
li
ke to program to a button in the
roof headli
ner.
40
Programming the button: Part 2 at the
radiator grille
6.
Hold the remote control up to the radiator
gri
ll
e on your vehicle¢
fig.
34.
7. Press and hold the remote control unt
il
the
tu rn signals on your vehicle blink. This may
take up to 30 seconds.
8.
If
t
he eme rgency flashers blink th ree times,
the programming was successful. If the
emergency flas hers only
blink
one t ime, t he
5 minute time limit for
t
he programming has
ended
or
t
he progr amming was not success-
ful. Repeat the programmi ng from the third
step, or try changing the distance to the radi-
ator grille
.
9. If the garage door or other system does not
open using the buttons in the roof headliner
even though the prog ramming was success-
ful
,
the system may use a rolling code in-
stead of a fixed
code.
Rolling code program-
ming
m ust be perfo rmed
¢
page
41.
The other two buttons in the roof headliner can
be programmed according to th
e
inst ruct ions
above.
Begin with the
t
hir
d st
ep.
Erasing button programming
The programmed buttons cannot be erased ind i-
vidually
.
They m ust all be erased together
.
Repro-
gram the buttons if
necessary.
..
Switch the ignit ion on.
..
Press and hold both outer buttons in the roof
headli
ner until the
LED@
turns off completely
(after about 20
seconds).
Reprogramming the button
s
..
Switch the ignition on
.
..
To reprogram an individua
l
butto n, press and
hold the button unt
il
the
LED@
starts to flash
quickly (after about 10
seconds).
Release the
button immed
iat
ely.
Programm ing mode is ac-
t ive
fo
r
5 m inutes.
.,.
Continue with t he fifth ste p.
@
Tips
-
Programming using the buttons in
t he
roof
headli ner
is not possible wit
h all
Info
tain
-
ment
systems.
If thi
s
is th
e case, program
Advertisement
