Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Uninet Manuals
  4. Printer
  5. DTF 1000
  6. Maintenance procedure

Uninet DTF 1000 Maintenance Procedure

Hide thumbs Also See for DTF 1000:
1
2
3
4
5

Advertisement

Quick Links

Download this manual
NOTE: These procedures are recommended in order to keep your UNINET DTF 1000 printer
functioning at optimal performance and to minimize printhead clogs and ink smudges. If you do not
follow these procedures and/or you suffer from a clog due to other circumstances (such as humidity
or other environmental deviations), you will need to do additional CLEANING CYCLES and possibly a
manual printhead flush (as a last resort) to help clean out any serious clog. Manual flushing should
not be done INSIDE the printer, as any liquid spills on the printer electronics can cause damage to
the printhead or printer boards. If a manual flushing is necessary, you should remove the printhead
from the printer and carefully flush it over a sink and away from printer components and electronics.
DO NOT RUN YOUR PRINTER IF THE PRINTHEAD IS WET. Manual flushing requires a 24 drying period
before powering on your printer, or you risk shorting out the head and motherboard.
The UNINET DTF 1000 Maintenance pack includes:
6 x Maintenance Cartridges (filled with Maintenance Solution)
1 x Cartridge Holder
100ml Maintenance Solution (EXTRA)
100ml Capping Solution
100ml De-Plasticizing Solution
6 x Damper Plugs
1 x Rubber Band
Cleaning Buds & Swabs
1 x Syringe for Wet Capping
1 x Damper Suction Syringe
1 x Syringe for filling the Maintenance Cartridges (for future re-filling, cartridges come pre-filled to start)
1 x Instructions for DAILY, WEEKLY and VACATION MODE Maintenance
UNINET DTF 1000 MAINTENANCE PROCEDURE
DAILY | WEEKLY | VACATION MODE

Advertisement

loading

Related Manuals for Uninet DTF 1000

Summary of Contents for Uninet DTF 1000

  • Page 1 UNINET DTF 1000 MAINTENANCE PROCEDURE DAILY | WEEKLY | VACATION MODE NOTE: These procedures are recommended in order to keep your UNINET DTF 1000 printer functioning at optimal performance and to minimize printhead clogs and ink smudges. If you do not...

  • Page 2: Daily Maintenance Procedure

    DAILY MAINTENANCE PROCEDURE This daily maintenance procedure should be done EVERY DAY (recommended), or at the most every other day. If you leave the printer idle for more than 2-3 days, your printer / printhead nozzles may need deep cleaning. See separate procedure for deep cleaning if needed. If you intend on leaving the printer idle for longer than 2-3 days, please use the VACATION MODE procedure shown further down.

  • Page 3: Weekly Maintenance Procedure

    2-3 days, and up to 2-4 weeks. Such as if you’re going on vacation. The items and components needed in this Vacation Mode Maintenance procedure are all included with the UNINET DTF 1000 Maintenance Pack. BEFORE YOU GO ON VACATION: Video: https://youtu.be/J8vo1W5ROpc...
  • Page 4 6. Remove the sealing plugs/tape from the breathing holes from the included maintenance cartridges (these are filled with UNINET maintenance solution). If you have used the maintenance cartridges before, make sure you insert them in the same order so that you do not contaminate any colors 7.
  • Page 5 WHEN YOU RETURN FROM VACATION: Video: https://youtu.be/J8vo1W5ROpc 1. Remove the maintenance cartridges (and remember to seal the breathing holes, so you can prevent leaks and keep the cartridges for future use), remove the elastic band, unplug the dampers and plug the dampers back into the printhead inlet ports (make sure you clean and keep the plugs for future use).