BST ekr 500 digital Installation And Commissioning Manual page 5

7.9.3 X100 ... 103 - Connection of CAN Bus Participants ..................................................... 73
8 Commissioning................................................................................................. 74
8.1 Safety Instructions ...................................................................................................... 74
8.2 Requirements.............................................................................................................. 75
8.3 Setting the DIL Switches of the Controller .................................................................. 76
8.3.1 DIL Switch Overview ................................................................................................... 76
8.3.2 Using the DIL Switch ................................................................................................... 77
8.3.3 Setting DIL Switch S4................................................................................................... 78
8.3.4 Setting DIL Switch S5................................................................................................... 79
8.3.5 Setting DIL Switch S6................................................................................................... 80
8.3.6 Setting DIL Switch S7................................................................................................... 80
8.4 Setting the DIL Switches of the Control Panel ............................................................ 81
8.5 Setting the Jumper...................................................................................................... 82
8.6 Checking the Device Addresses .................................................................................. 83
8.6.1 Controller Device Address........................................................................................... 83
8.6.2 Control Panel Device Address ..................................................................................... 84
8.7 Setting the Terminating Resistors............................................................................... 85
8.7.1 Terminating Resistor of the Controller ....................................................................... 85
8.7.2 Terminating Resistor of the Control Panel.................................................................. 87
8.8 Calling up the Setup Menu.......................................................................................... 89
8.9 Setting the Dimension Unit......................................................................................... 92
8.10 Setting the Motor Rotation Direction ......................................................................... 93
8.11 Commissioning the Actuator Without Position Feedback .......................................... 94
8.11.1 Setting the Guiding Direction for Center Positioning.................................................. 94
8.11.2 Setting the Gain of the Servo Center Transducer ....................................................... 95
8.12 Commissioning the Actuator With Position Feedback................................................ 97
8.12.1 Setting the Guiding Direction for Center Positioning.................................................. 97
8.12.2 Setting Stroke Limitation and Servo-Center Position.................................................. 98
8.12.3 Activating the Normalized Display of the Actuator Position..................................... 101
8.12.4 Activating Position Control ....................................................................................... 104
8.13 Setting the Guiding Direction.................................................................................... 105
8.13.1 Guiding Direction for Web Edge Guiding and Web Center-Line Guiding (Sensor 1/2) . 105
8.13.2 Guiding Direction for Line / Contrast / Feature Guiding (Sensor 3).......................... 106
8.14 Performing the Material Setup ................................................................................. 106
8.15 Adjusting the Controller Gain ................................................................................... 107
8.16 Commissioning the CCD Camera............................................................................... 109
8.16.1 CCD Camera Calibration............................................................................................ 109
8.16.2 Material Thickness Compensation............................................................................ 113
8.16.3 Setting the Material Thickness (After Changing the Material).................................. 116
8.16.4 Entering the Position Offsets .................................................................................... 117
8.17 Commissioning the Sensor Positioner ...................................................................... 119
8.17.1 Calling Up the Setting Menu ..................................................................................... 119
8.17.2 Overview Setting Menu ............................................................................................ 120
8.17.3 Activating Retract Mode ........................................................................................... 121
8.17.4 Activating Automatic Setpoint Acceptance .............................................................. 122
8.17.5 Setting Automatic Sensor Tracking ........................................................................... 123
8.17.6 Activating Automatic Edge Sensor Standardization.................................................. 124
8.17.7 Entering the Position Offset for the Sensor Slides .................................................... 125
8.18 Commissioning the Positioning Unit ......................................................................... 127
8.18.1 Utilization.................................................................................................................. 127
8.18.2 Calling Up the Setting Menu ..................................................................................... 128
8.18.3 Overview Setting Menu ............................................................................................ 128
8.18.4 Reversing the Operating Direction of the Arrow Keys .............................................. 129
8.18.5 Entering the Position Offset for the Sensor Slides .................................................... 131
8.19 Commissioning the Electronic Remote Precision Adjustment (Optional)................. 133
8.19.1 EFE 1.......................................................................................................................... 133
8.19.2 EFE 1000.................................................................................................................... 134
ekr 500 digital Unit Touch - Installation and Commissioning Manual
Table of contents
v