Table of Contents
Advertisement
en Suitable cookware
Suitable cookware
4 Suitable cookware
Cookware that is suitable for induction cooking must
have a ferromagnetic base, i.e. it must be attracted by
a magnet. The base must also match the size of the
cooking zone. If cookware is not detected on a cooking
zone, place this on the cooking zone with the next
smallest diameter.
Cookware
Recommended cook-
ware
Suitable
Not suitable
Notes
¡ Do not use adapter plates between the hob and the
cookware.
Installation and connection
5 Installation and connection
You can find out where and how best to install your ap-
pliance here. You will also learn how to connect your
appliance to the power supply.
5.1 Electrical connection
The appliance must be connected to the mains by a li-
censed expert. You must comply with the requirements
of your electricity supplier.
¡ Your appliance comes with the enclosed cable for
permanently connecting it to the mains electricity
supply. In the event of damage, never remove the
cable from the appliance or replace it with another
cable (with or without plug).
¡ If the power cable of this appliance is damaged, this
must be replaced by the manufacturer, the manufac-
turer's customer service or a similarly qualified per-
son in order to prevent any risk.
¡ Any damage arising from the appliance being con-
nected incorrectly will invalidate the warranty.
Information on electrical connection by our customer
service:
¡ Connect the appliance in accordance with the spe-
cifications on the rating plate.
8
Materials
Stainless steel cookware in a sandwich
design that distributes the heat well.
Ferromagnetic cookware made of enamelled
steel, cast iron or special induction cookware
made of stainless steel.
The base is not fully ferromagnetic.
Cookware bases that contain aluminium.
Cookware made from normal thin steel,
glass, clay, copper or aluminium.
4.1 Size and characteristics of the cookware
To be able correctly detect the cookware, you must
take the size and the material of the cookware into con-
sideration. All cookware bases must be perfectly flat
and smooth.
Use Cookware test to check whether the cookware is
suitable. Refer to
→ "Cookware test", Page 17 for more details.
Properties
This cookware distributes the heat evenly,
heats up quickly, and ensures that it can be
detected easily.
This cookware distributes the heat evenly,
heats up quickly, and ensures that it can be
detected.
If the ferromagnetic area is smaller than the
base of the cookware, only the area that is
ferromagnetic heats up. As a result, the heat
is not distributed evenly.
These cookware bases reduce the ferromag-
netic area, which means that less power is
emitted to the cookware. This cookware may
not be sufficiently detected or may not be de-
tected at all, and therefore does not heat suf-
ficiently.
¡ Do not heat up empty cookware and do not use
cookware with a thin base, as this may become very
hot.
¡ The appliance must only be connected to an elec-
trical connection that corresponds to the applicable
regulations. The socket must be easily accessible
so that you can disconnect the appliance from the
electricity supply if necessary.
¡ Ensure that a multi-pin disconnecting system is
available.
¡ For safety reasons, this appliance must only be con-
nected to an earthed connection. If the safety earth
terminal does not comply with regulations, protec-
tion against electrical risks is not guaranteed.
¡ To connect the appliance, use H 05 VV-F cables or
other equivalent cables.
Information on the electrical connection by the
installer:
¡ If the plug is not accessible following installation, an
all-pole isolating unit with a contact clearance of at
least 3 mm must be available on the installation
side. This is not necessary if the appliance is con-
nected via a plug that is accessible to the user.
¡ Electrical safety: The cooker corresponds to safety
class I and may only be used in conjunction with a
safety earth terminal.
Advertisement
Table of Contents
