Table of Contents
Related Manuals for Alliance Laundry Systems SDE807
Summary of Contents for Alliance Laundry Systems SDE807
- Page 1 Clothes Dryer Nonmetered and Metered Electric and Gas Models D677I Keep These Instructions for Future Reference. (If this machine changes ownership, this manual must accompany machine.) Part No. 512680R5 www.comlaundry.com September 2009...
- Page 3 • A “T-Handle” type gas shut-off valve must be installed in the gas supply line to this appliance. • This appliance must not be installed in a bedroom or bathroom. 512680 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
-
Page 4: Table Of Contents
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680... - Page 5 Control Panel ................... 45 Exhaust System ................45 Lint Filter ....................46 Motor Overload Protector..............46 For Energy Conservation..............46 Troubleshooting .................. 47 Contact Information................48 Installer Checklist..............Back Cover © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680...
-
Page 6: Safety Information
12. ALWAYS clean the lint filter after every load. A layer of lint in the filter reduces drying efficiency and prolongs drying time. 512680 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT... - Page 7 Always contact your dealer, distributor, service agent or the manufacturer about any problems or conditions you do not understand. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680...
-
Page 8: Installation
15.4 in. (59.7 cm) (71.1 cm) (39.1 cm) 26.9 in. (68.3 cm) DRY2237N GAS MODELS DRY2237N *With leveling legs turned into base. 3/8 in. N.P.T. Gas Connection 512680 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT... -
Page 9: Metered Models
For maximum housing. drying performance, we recommend that more clearance be allowed around the dryer than the clearances that are listed throughout this manual. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680... -
Page 10: Before You Start
WARNING 7.21 in. (18.31 cm) coin drawer. Any disassembly requiring the use of tools must be performed by a suitably qualified service person. W299 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680... -
Page 11: Installing The Dryer
The dryer must not rock. D678I D678I Dryer Base Level Leveling Leg Rubber Foot Figure 3 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680... - Page 12 Outer Wall of Enclosure **NOTE: For new installations, locate top of wall vent 42 inches (106.7 cm) above floor to make venting easier to connect. Figure 4 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680...
-
Page 13: Step 2: Connect Dryer Exhaust System
Dryer exhausts 220 cfm (measured at back of system to assure safe operation. W749 dryer). DO NOT install flexible duct in concealed spaces, such as a wall or ceiling. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680... -
Page 14: Exhaust Direction
Directional Exhaust Kit, contractor or building material suppliers. 528P3, available as optional equipment at extra cost. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680... -
Page 15: Exhaust System
NOTE: The maximum length of 4 in. (10.2 cm) diameter flexible metal duct must not exceed 7.87 feet (2.4 m) as required to meet UL2158, clause 7.3.2A. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680... -
Page 16: Multi-Dryer Installation Exhaust Requirements
58786 Backdraft Damper (Available through Weather Hood or Sweep Elbow your local authorized parts source) (No cap or screen) Clean Out Cover (Must be provided). Inspect monthly. Figure 6 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680... - Page 17 2 in. (5 cm) Minimum NOTE: Where the exhaust duct pierces a combustible wall or ceiling, an opening must be sized as shown or per local codes. Figure 8 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680...
-
Page 18: Step 3: (Gas Dryer Only) Connect Gas Supply Pipe
• Do not use an open flame to check for gas leaks. Use a non-corrosive leak detection fluid. • Any disassembly requiring the use of tools must be performed by a suitably qualified service person. W316 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680... -
Page 19: Step 4: (Electric Dryer Only) Connect Electrical Plug
For proper operation at altitudes above 3500 feet (1070 m) the L.P. gas valve spud orifice size must be reduced to ensure complete combustion. Refer to Table 3. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680... - Page 20 The power cord connection between wall receptacle and dryer terminal block IS NOT supplied with dryer. Type of power cord and gauge of wire must conform to local codes. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680...
- Page 21 Ground to Neutral Wire Neutral Terminal “L2” Terminal Center Wire (Neutral) Strain Relief (Not supplied with dryer) Ground Screw “L1” Terminal Black Wire White Wire (Neutral) Red Wire Figure 11 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680...
- Page 22 3. Use a strain relief and insert end of power cord through power supply hole. 2. Remove access cover from rear of dryer. D696I D695I Figure 14 Figure 13 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680...
- Page 23 8. Reinstall access cover and screw. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680...
- Page 24 10. Reinstall access cover and screw. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680...
-
Page 25: Step 5: Reverse Door, If Desired
3. Pull bottom of door liner out, then pull down, removing door liner from door panel. DRY1918N DRY1918N Figure 26 7. Reinstall nine screws removed in Step 2. DRY1916N DRY1916N Figure 23 DRY1919N DRY1919N Figure 27 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680... -
Page 26: Step 6: Wipe Out Inside Of Dryer
Do not use an extension cord. Do not operate both a washer and gas dryer on D604I the same circuit. Use separetely fused 15 amp D604I circuits. Figure 30 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680... - Page 27 NOTE: Have a qualified electrician check the polarity of the wall receptacle. If a voltage reading is measured other than that illustrated, the qualified electrician should correct the problem. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680...
-
Page 28: Step 8: Recheck Steps 1-7
STARTING SERIAL NO. 0804 D700I DRY2235N Closed Position 1/8 in. (3.1 mm) Pipe Plug Shut-Off Valve Handle (For checking manifold pressure) Air Shutter Lockscrew Open Position Air Shutter Figure 33 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680... -
Page 29: Vending
The timer will not count down until the Start button is pressed. Run Mode In Run Mode, the control is running a cycle. The IN USE LED is lit. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680... -
Page 30: Error Display Mode
The additional cool down time is added to the factory default minimum cool down time of 3 minutes. A value of 1 to 3 additional minutes is available. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680... -
Page 31: Dipswitch Settings
Vending Dipswitch Settings Heat Switch Number Heat Time Per Coin Pulse (in minutes) Table 4 (continued) © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680... -
Page 32: Models Through Serial No. 0908
Models Through Serial No. 0908 Cool Down Per Cycle Cool Down Switch Number (in minutes) 3 (preset at factory) Total Cycle Time = Heat Time + Cool Down Time Table 5 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680... -
Page 33: Models Through Serial No. 0909
Then set them all to the off position. Refer to original settings. Figure 34. 5. Plug in the machine. 1 2 3 4 5 6 7 8 DRY2225P DRY2225P Figure 34 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680... -
Page 34: Slide Extension
(shims) (use number of washers included in kit) and nut. Refer to Figure 36. Make sure washers are flat against bracket. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680... - Page 35 The IN USE light will turn on, or flash if it is already on, to indicate proper operation. NOTE: To avoid long run-down time (45 minutes factory default) when testing operation, refer to Test Setting section. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680...
-
Page 36: Additional Dryer Security
Double “D” Hole IMPORTANT: Do not use a power driver to tighten screw. Torque of a power driver could over-tighten Figure 39 screw causing damage to cabinet assembly. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680... -
Page 37: Operation
Clean lint filter before each use. Figure 41 Step 3: Close Loading Door Close loading door. Dryer will not operate with the door open. D608I D608I Figure 40 D688I D688I Figure 42 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680... -
Page 38: Step 4: Set Fabric Selector
60 minutes). Press the PUSH-TO-START button. without heat, up to 18 hours or until door is IN USE light will come on (indicating start of cycle). opened. NONMETERED MODELS DRY2101N Figure 44 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680... -
Page 39: Operation Instructions For Electronic Display Control Dryers
Clean lint filter before each use. Figure 47 Step 3: Close Loading Door Close loading door. Dryer will not operate with the door open. D608I D608I Figure 46 D688I D688I Figure 48 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680... -
Page 40: Step 4: Set Fabric Selector
Remove knits when slightly damp because overdyring may cause shrinkage. Do not tumble dry knit woolens. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680... -
Page 41: Step 6: Start Dryer
When the START pad is pressed, the cycle will begin or resume. The PUSH START status word flashes at one-second intervals when activated. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680... -
Page 42: Operation Instructions For Mdc Dryers
Clean lint filter before each use. Step 3: Close Loading Door Close loading door. Dryer will not operate with the door open. D608I D608I Figure 53 D688I D688I Figure 55 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680... -
Page 43: Step 4: Set Fabric Selector
COOL DOWN is lit whenever the COOL DOWN portion of a heated cycle is active. It is also lit when no heat is programmed for a cycle in operation. DRY1927N Figure 58 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680... -
Page 44: Operation Instructions For Netmaster Dryers
Clean lint filter before each use. Figure 61 Step 3: Close Loading Door Close loading door. Dryer will not operate with the door open. D608I D608I Figure 60 D688I D688I Figure 62 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680... -
Page 45: Step 4: Set Fabric Selector
Remove knits when slightly damp because overdrying may cause shrinkage. Do not tumble dry knit woolens. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680... -
Page 46: Step 6: Start Dryer
It will also flash alternately with ADD TIME when a card is inserted while a cycle is running or when a card is left in the reader. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680... -
Page 47: Maintenance
NOTE: The wiring diagram is located inside the control panel. WARNING Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. W049 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680... -
Page 48: Lint Filter
PUSH-TO-START button or START pad. If overload protector cycles again, remove the dryer from use and call the service person to correct the problem. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680... -
Page 49: Troubleshooting
Check room for odors before drying clothes. Any odor (fried foods, paint, Clothes have odor varnish, cleaners, burning wood, etc.) will transfer to clothing as the dryer draws air from the room. Ventilate room before drying clothes. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 512680... -
Page 50: Contact Information
The nameplate will be in the location shown in the illustration below. Please include a copy of your bill of sale and any service receipts you have. D063K Nameplate Figure 68 512680 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT... -
Page 52: Installer Checklist
• Check for Gas Leaks. • Check Heat Source. D258I CHECK CHECK ELECTRIC ONLY • Connect Electrical Cord. CHECK W315IE0A D699I • Reverse Door, if Desired. CHECK W675I D675I © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
Need help?
Do you have a question about the SDE807 and is the answer not in the manual?
Questions and answers