Related Manuals for Bosch SMV2ITX23E
Summary of Contents for Bosch SMV2ITX23E
- Page 1 Translated from German to English - www.onlinedoctranslator.com dishwasher SMV2ITX23E [en] Instructions for use...
-
Page 2: Table Of Contents
Further information and explanations can be found online: Table of contents 1 Security ........4 8.2 Lower dish rack....21 1.1 General information ....4 8.3 Folding spines........ 22 1.2 Intended 8.4 Cutlery basket ......22 use ........... 4 9 Before first use ....23 1.3 Restriction of the user group ........... - Page 3 14 Basic operation..32 21 Technical data ....53 21.1 Information on free and open 14.1 Switching on the device ....32 source software ..53 14.2 Setting the program ..... 32 14.3 Setting additional functions ..32 22 Declaration of Conformity ... 54 14.4 Setting the time delay ...
-
Page 4: Security
deSecurity 1 Security Please note the following safety instructions. 1.1 General information ¡Read these instructions carefully. ¡Save the instructions and product information later use or subsequent ownership. ¡Do not connect the device if it is damaged during transport. 1.2 Intended use Use the device only: ¡to wash household dishes. - Page 5 Securityde WARNING - Risk of electric shock! Improper installations are dangerous. ▶ Only connect and operate the device in accordance with the information on the nameplate. ▶ Always use the power cable supplied with the new device. ▶ Only connect the device to an alternating current power supply via a properly installed earthed socket.
-
Page 6: Safe Use
deSecurity Contact between the device and installation cables can lead to a defect in the installation cables, e.g. E.g., gas pipes and power lines. Gas from a corroded gas line can ignite. A damaged power line can lead to a short circuit. ▶... - Page 7 Securityde Strongly caustic-alkaline or highly acidic cleaning agents in conjunction with aluminum parts in the washing compartment of the device can lead to explosions. ▶ Never use highly caustic-alkaline or highly acidic cleaning agents, especially from the commercial or industrial sector, in conjunction with aluminum parts (e.g.
-
Page 8: Damaged Device
deSecurity ▶ Never bend, squeeze or change the power cable. 1.6 Damaged device WARNING - Risk of electric shock! A damaged device or a damaged power cable is dangerous. ▶ Never operate a damaged device. ▶ Never operate a device with a cracked or broken surface. ▶... - Page 9 Securityde Children can inhale or swallow small parts and thereby suffocate. ▶ Keep small parts away from children. ▶ Do not let children play with small parts. Children can become trapped in the device and suffocate. ▶ If available, use parental controls. ▶...
-
Page 10: Avoid Material Damage
deAvoid property damage Contact between the device and 2 property damage water pipes may cause corrosion of avoid the water pipe and the water pipe may leak. Make sure there is at least 5 cm ▶ 2.1 Safe Installation distance between the device and the water pipe. -
Page 11: Environmental Protection And Saving
Environmental protection and savingde Special salt for dishwashers can 3.2 Save energy damage the washing container If you follow these instructions, your through corrosion. device will use less electricity and ▶ To ensure that overflowed special water. salt is rinsed out of the rinsing container, fill the special salt into the Use the Eco 50°... -
Page 12: Device
deSetting up and connecting The delivery consists of: ¡ 4.3 Waste water connection dishwasher Connect your device to a wastewater ¡Instructions for use connection so that water ¡assembly Instructions contaminated by the rinse cycle can ¡Further information documents ¡ drain away. Mounting material ¡Vapor protection Install waste water connection... -
Page 13: Electrical Connection
Setting up and connectingde Connect the device to the drinking water connection using the included parts. Observe the technical data. Make sure that the drinking water connection is not kinked, crushed or twisted. 4.5 Electrical connection Connect the device electrically Hints ¡Observe the safety instructions wise →... -
Page 14: Getting To Know Each Other
Get to know 5 Get to know 5.1 Device Here you will find an overview of the components of your device. type label Type plate with E number and FD number → Page 52 . You need the data for customer service → Page 52 . - Page 15 Get to knowde Fill the cleaner chamber with cleaner. Cleaner chamber → "Cleaner", page 27 Lower dish rack → Page 21 Lower dish rack Fill the special salt storage container with Storage container for special special salt. salt → "Softening system", page 23 Lower spray arm The lower spray arm cleans the dishes in the lower basket.
-
Page 16: Controls
deGet to know 5.2 Controls You can use the control panel to set all of your device's functions and receive information about its operating status. Some buttons allow you to perform various functions. 4 5 6 7 8 9 141312 11 Switch on device →... - Page 17 Get to knowde programs Program buttons and additional → "Programs", page 18 functions Additional functions → "Additional functions", page 20 Open the device door. Door handle Home Connect → Page 38 WiFi display Rinse aid refill indicator Rinse aid system →...
-
Page 18: Programs
programs 6 programs H Here you will find an overview of If the rinse aid system is switched on or if the adjustable programs. Depending there is a lack of rinse aid, the running time on the device configuration, various changes. -
Page 19: Information For Test Institutes
programsde program Program Sequence → "Favorite ", page 19 Favorite A notice:The comparatively longer ¡To set the program to the factory running time in the Eco 50° program To reset the pre-rinse program results from longer soaking and drying stored on the page, use the Home times. -
Page 20: Additional Functions
Additional functions Additional functions Here you will find an overview of the additional functions that can be set. Depending on Device configuration, various additional functions are available, which you can find on the control panel of your device. Depending on the program, you can choose certain additional functions. -
Page 21: Upper Dish Rack
Furnishingde Hang the dish rack on the upper 8.1 Upper dish rack rollers (level 3) or lower rollers Place cups, glasses and small dishes in (level 1). the top rack. Make sure the dish rack is at the same height on both sides. To create space for larger dishes, you Insert the dish rack. -
Page 22: Folding Spines
deFurnishing Push the lever forward and fold down the folding spikes 8.3 Folding spines Use the folding spikes to safely sort To use the folding spikes again, dishes, e.g. B. Plates. fold them up. aThe folding spines click audibly 8.4 Cutlery basket Always put cutlery in the cutlery basket unsorted and with the pointed side down. -
Page 23: Before First Use
Before first usede Fill in the cleaner 9 Before the first → Page 27 . Start the program with the highest cleaning temperature without dishes. 9.1 Carry out initial We recommend operating the commissioning device without dishes before first use due to possible water stains and You must make settings when you other residues. -
Page 24: Setting The Softening System
deSoftening system Press repeatedly until the appropriate water hardness level is set. A notice:Set your device to the determined water hardness level. → "Setting the softening system", 0, 1, 2 or 3 LEDs light up page 24 accordingly. If the water hardness level is 0 - 6 °dH, →... -
Page 25: Switching Off The Softening System
Softening systemde 10.4 Switch off the softening Pour into the special salt storage container before starting the program. system If the special salt refill indicator Unscrew and remove the lid from bothers you, e.g. B. if you use the special salt storage container. combined cleaners with salt substitutes, you can switch off the When using for the first time: Fill... -
Page 26: Regenerating The Softening System
deRinse aid system 10.5 Regenerate the softening 1 1 rinse aid system system In order to maintain the trouble-free 11.1 Rinse aid function of the softening system, the device regenerates the softening For optimal drying results, use rinse system at regular intervals. aid. -
Page 27: Setting The Amount Of Rinse Aid Added
cleanserde Overflowing rinse aid can lead to 11.3 Switch off the rinse aid excessive foam formation during system the rinse cycle. Close the lid of the rinse aid If the rinse aid refill indicator bothers reservoir. you, for example if you use combined detergents with a rinse aid aThe lid clicks into place audibly. - Page 28 decleanser Enzymes break down starch and Solo Cleaner dissolve protein. To remove colored Solo cleaners are products that do not stains, oxygen-based bleaches are contain any other components apart usually used, e.g. B. for tea or from the cleaner, e.g. B. powder ketchup.
-
Page 29: Unsuitable Cleaners
cleanserde ¡Even if the rinse aid refill 12.2 Unsuitable cleaners indicator and the special salt refill Do not use cleaners that could cause indicator light up, washing damage to the device or endanger programs run smoothly when using health. combined cleaners. Hand dishwashing liquid ¡The function of the rinse aid is Hand dishwashing detergent can... -
Page 30: Tableware
deDishes Close the cleaner chamber lid. 13.1 Damage to glass and dishes Only wash glasses and porcelain that are marked as dishwasher-safe by the manufacturer. Avoid damage to glass and dishes. Caused Recommendation Just rinse The following thing Dishes, that dishes are not dishwasher from manufacturer... -
Page 31: Putting Away The Dishes
Dishesde ¡For better washing results and Caused Recommendation To maintain drying results, place If you are strong Strong caustic alkaline parts with bulges and depressions ash or strong caustic alkaline at an angle to allow water to drain acidic rice or strongly acidic away. -
Page 32: Clearing Out The Dishes
deBasic operation – Do not place any small parts in 1 4 basic the tab collecting tray and do not service block it with dishes so as not to block the lid of the detergent compartment. 14.1 Switch on the device press. -
Page 33: Start Program
Basic operationde Press the button for the ▶ ¡You can view the current program Only change the program if you appropriate additional function. → cancel the program. "Additional functions", page 20 → "Cancel program", page aThe additional function is set and the additional function button flashes. -
Page 34: Switching Off The Device
deBasic operation 14.8 Switch off the device The instructions for safe use → Page 10 observe. press. Tip:If you press during the rinse cycle, the current program will be interrupted. When you turn on the device, the program continues automatically. -
Page 35: Basic Settings
Basic settingsde 1 5 basic settings S You can adjust the basic settings of your device to suit your needs. 15.1 Overview of the basic settings The basic settings depend on the features of your device. Basic setting Description Selection Scale with 4 levels Adjust the water Water hardness... - Page 36 deBasic settings Basic setting Description Selection Remote start Scale with 3 levels Activate or deactivate the function. → "Activate Remote Start", page 37 This basic setting is only available after you have connected the device to the Home Connect app. →...
- Page 37 Basic settingsde Press repeatedly until the To open the device settings, appropriate signal volume is set. 3 seconds press. flashes. press repeatedly until flashes. Press repeatedly until the LEDs show the appropriate value. 0, 1, 2 or 3 LEDs light up accordingly.
-
Page 38: Home Connect
deHome Connect 16.1 Home Connect quick start 1 6 Home Connect This device is network capable. Connect your device to a mobile device Connect your device to a mobile device quickly and easily. to operate functions via the Home Connect app. The Home Connect services are not available in every Set up the Home Connect app country. -
Page 39: Remote Start
Cleaning and carede Categories of data to the 16.2 Remote Start Home Connect server You can start the device with your (Initial registration): mobile device using the Home ¡Unique device identifier (best Connect app. based on device keys and the MAC address of the installed Wi-Fi Tip:If you permanently activate this communication module). -
Page 40: Cleaning Agents
To avoid cleaner for dishwashers online at malfunctions and reduce odors, clean https://www.bosch-home.com/store the device at regular intervals. or via customer service. Machine care is a program that Machine care, in conjunction with... -
Page 41: Sieve System
Cleaning and carede If the machine care indicator on the Pour the machine cleaner into the control panel lights up or the display cleaner chamber until it is advises you to do so, carry out the completely full. machine care without dishes. After you Do not add machine cleaner to the have carried out the machine interior of the device. - Page 42 deCleaning and care Turn the coarse sieve Clean the sieve elements under counterclockwise and remove the running water. sieve system. Carefully clean the dirt edge Make sure that no foreign objects between the coarse sieve and fine ‒ fall into the pump pot. sieve.
-
Page 43: Cleaning The Spray Arms
Cleaning and carede 17.6 Clean spray arms Limescale and impurities from the rinse water can block the nozzles and bearings of the spray arms. Clean the spray arms regularly. Unscrew the upper spray arm and pull it downwards. Pull the lower spray arm upwards. Check the outlet nozzles of the spray arms for blockages under running water and remove foreign bodies if... -
Page 44: Troubleshooting
Troubleshooting information before contacting customer service. This way you avoid unnecessary costs. Tip:Further information and explanations for troubleshooting can be found online by scanning the QR code in the table of contents and on our website www.bosch-home.com. WARNING Danger of electric shock! Improper repairs are dangerous. - Page 45 Troubleshootingde Cause and troubleshooting Disturbance Screw on the water connection. Display for water supply 8th. Check the water connection for leaks. running lights up Connect the power supply. Turn on the device. Sieves are dirty or clogged. Clean the sieves. ▶...
- Page 46 deTroubleshooting Cause and troubleshooting Disturbance There is a technical malfunction. “Water supply” display Press . "Check running" flashes Unplug the device or turn off the fuse. Wait at least 2 minutes. Insert the power plug of the device into a socket or switch on the fuse.
- Page 47 Troubleshootingde Cause and troubleshooting Disturbance Spray arm rotation of the lower spray arm is Leftover food on dishes blocked. dishes. Arrange the dishes so that the dishes do not ▶ hinder the rotation of the spray arm. Spray arm nozzles are clogged. Clean the spray arms →...
- Page 48 deTroubleshooting Cause and troubleshooting Disturbance Adjust the upper dish rack to the same height on ▶ Leftover food on dishes the left and right. dishes. → "Upper dish rack", page 21 Removable streaks The amount of rinse aid added is set too high. are located on glasses, Set the rinse aid system to a lower level.
- Page 49 Troubleshootingde Cause and troubleshooting Disturbance The detergent chamber was damp when the detergent was There are cleaning residues in the detergent filled. chamber or in the Only pour cleaner into a dry cleaner chamber. ▶ tab collecting tray. Refill indicator for Special salt is missing.
-
Page 50: Cleaning The Waste Water Pump
deTransport, storage and disposal Insert the pump cover and press 18.1 Clean the waste water 8th. down. pump Coarse food residue or foreign objects can block the wastewater pump. As soon as the flushing water no longer drains properly, you have to clean the wastewater pump. -
Page 51: Making The Device Frost-Proof
Transport, storage and disposalde 19.2 Make the device frost- 19.4 Dispose of old device proof Valuable raw materials can be reused through environmentally If the device is in a room at risk of friendly disposal. frost, e.g. B. in a holiday home, empty the device completely. -
Page 52: Customer Service
Customer service 20.2 AQUA-STOP guarantee 0 customer service In addition to warranty claims against Function-relevant original spare the seller from the purchase contract parts in accordance with the relevant and in addition to our manufacturer's Ecodesign Regulation are available guarantee, we provide replacement from our customer service for a under the following conditions. -
Page 53: Technical Data
Technical datade 2 1 Technical data Weight Max.: 60kg Tension 220 - 240V, 50Hz or 60Hz 2000 - 2400 W Connection value validation 10 - 16 A ¡at least 50 kPa (0.5 bar) ¡ Water pressure max. 1000 kPa (10 bar) at least 10 l/min Inflow quantity Cold water. -
Page 54: Declaration Of Conformity
2 declarations of conformity provisions of Directive 2014/53/EU. tion You can find a detailed RED declaration of conformity online at www.bosch- BSH Hausgeräte GmbH hereby home.com on the product page of declares that the device with Home your device among the additional Connect functionality is in accordance documents. - Page 56 Contact data of all countries are listed in the attached service directory. BSH Hausgeräte GmbH Carl-Wery-Strasse 34 81739 Munich, GERMANY www.bosch-home.com A Bosch Company *9001881047* 9001881047(030707) 642 E5 de...
Need help?
Do you have a question about the SMV2ITX23E and is the answer not in the manual?
Questions and answers