Operate the device only from the type of power source indicated on the label. – Unless qualified, do not attempt to service a damaged device yourself. Refer all servicing to qualified service personnel. Bosch Security Systems B.V. 2023-11 | V01 | F.01U.408.367 User manual...
Notice! Video loss is inherent to digital video recording; therefore, Bosch Security Systems cannot be held liable for any damage that results from missing video information.
Page 7
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Responsible party Bosch Security Systems Inc Bosch Security Systems B.V. 2023-11 | V01 | F.01U.408.367 User manual...
Page 8
FLEXIDOME micro 3100i 130 Perinton Parkway 14450 Fairport, NY, USA For more information please contact the nearest Bosch Security Systems location or visit: www.boschsecurity.us Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Page 9
Security advisories, that is a list of identified vulnerabilities and proposed solutions: https://www.boschsecurity.com/xc/en/support/product-security/security- advisories.html Bosch assumes no liability whatsoever for any damage caused by operating its products with outdated software components. Old electrical and electronic equipment This product and/or battery must be disposed of separately from household waste.
If you cannot connect, the unit may have reached its maximum number of connections. Depending on the device and network configuration, each unit can have up to 50 web browser connections, or up to 100 connections via Bosch Video Client or BVMS. Password protection in camera The device is password-protected.
Page 11
Fill in the fields User name and Password. Click OK. If the password is correct, the desired page appears. Note: New releases of software may require you to set a new and stronger password. Bosch Security Systems B.V. 2023-11 | V01 | F.01U.408.367 User manual...
Click this icon to configure the device. Dashboard Click this icon to see detailed system information. Links Click this icon to navigate to the Bosch download store. Logout Click this icon to log out of the device. Click this icon to get context-sensitive help for the page you are browsing.
The Dashboard is only visible in the application bar if the Show 'Dashboard' option is enabled by a service-level user in the Configuration -> Web Interface -> Appearance page. Bosch Security Systems B.V. 2023-11 | V01 | F.01U.408.367 User manual...
If you hover over the right-hand icon, the network load is shown. This information can help with problem solving or when fine tuning the unit. For example: – if the storage activity is too high, change the recording profile, 2023-11 | V01 | F.01U.408.367 Bosch Security Systems B.V. User manual...
Expand the Connection group on the left side of the browser. To view a recording stream: – Click the Recording drop-down arrow to see the options. – Select one of the numbered recording streams. Bosch Security Systems B.V. 2023-11 | V01 | F.01U.408.367 User manual...
The Dashboard page shows information on 4 topics: – Device status – Recording status – Connection Status – Services You can also download a .JSON file with information about the device: 2023-11 | V01 | F.01U.408.367 Bosch Security Systems B.V. User manual...
Page 17
Operation via the browser | en At the bottom of the page, locate the Export button Click the Export button Select a location in your hard drive to store the file Bosch Security Systems B.V. 2023-11 | V01 | F.01U.408.367 User manual...
Certificate. A check mark in this check box indicates that at least one certificate is loaded onto the device. The Trusted certificate is a root certificate for Bosch Security Systems that proves that the device meets the following criteria: –...
Configuration | en – It has not been tampered with. The Trusted certificate is issued by Escrypt. Escrypt is a Bosch company and Certificate Authority (CA). – Active Directory server (AD FS). A check mark in this check box indicates that the device uses an active directory server.
The default language is English. After setting the new language, the page refreshes automatically. The GUI now displays field names and options, as well as OSD messages, in the selected language. 2023-11 | V01 | F.01U.408.367 Bosch Security Systems B.V. User manual...
Page 21
You can specify the interval at which the individual images should be generated for the M- JPEG image on the Live page. Enter a time interval (in milliseconds). The default is 0. Bosch Security Systems B.V. 2023-11 | V01 | F.01U.408.367 User manual...
Four separate accounts can be defined for posting and recording export. Type Select the account type. Account name Enter an account name to be shown as the target name. IP address Enter the IP address for an FTP server. 2023-11 | V01 | F.01U.408.367 Bosch Security Systems B.V. User manual...
To transfer the IP address of the device, click the Register button. Status The status of the DynDNS function is displayed here for information purposes; these settings cannot be changed. Click Set to apply the changes. Bosch Security Systems B.V. 2023-11 | V01 | F.01U.408.367 User manual...
Click Restore to restore all settings, except network settings, to their defaults. Note: Clicking this button also clears the service-level password. Operators must reset the password before doing anything else. 2023-11 | V01 | F.01U.408.367 Bosch Security Systems B.V. User manual...
If you have enabled the Transparent background option, the background color is not displayed in the OSD. Optionally, tick the Underlay with full-width bar box to place a full-width background-bar beneath the time stamp. Bosch Security Systems B.V. 2023-11 | V01 | F.01U.408.367 User manual...
Page 26
Enter the message to be displayed on the image in the event of an alarm. The maximum text length is 32 characters. – Text color Select the color for the alarm message to be displayed in. – Background color 2023-11 | V01 | F.01U.408.367 Bosch Security Systems B.V. User manual...
Enter the height in meters of the position of the camera. The height describes the vertical distance from the camera to the ground plane of the captured image. Typically the elevation of the mounted camera above the ground. Bosch Security Systems B.V. 2023-11 | V01 | F.01U.408.367 User manual...
Page 28
A line on ground corresponds to a line that is on the ground plane, such as a road marking. 2023-11 | V01 | F.01U.408.367 Bosch Security Systems B.V. User manual...
Page 29
Y-axis (Cartesian), the azimuth is 90°. WGS 84 The WGS 84 coordinate system is a spherical coordinate system description of the world and used in many standards including GPS. Bosch Security Systems B.V. 2023-11 | V01 | F.01U.408.367 User manual...
Option in field “White Additional fields for NOTES balance” configuration Basic auto The three fields R-gain, G-gain, and B-gain only appear when the hold Standard auto button is pushed. Sodium lamp auto 2023-11 | V01 | F.01U.408.367 Bosch Security Systems B.V. User manual...
Select one of the available High dynamic range options below: – Off - The device is in single exposure mode and the user does not have an increased dynamic range through HDR. Bosch Security Systems B.V. 2023-11 | V01 | F.01U.408.367 User manual...
Active profile shows the profile that is in use and can be set differently per stream If no edge recording or VRM recording is active, the device switches to the Non-recording profile. Please refer to section Non-recording profile. (Only applicable to 2MP models) 2023-11 | V01 | F.01U.408.367 Bosch Security Systems B.V. User manual...
Page 33
Profile 4 Image Optimized For a reduced resolution image, the video bit rate and frame quality are adjusted to ensure that the picture quality is the priority. Bosch Security Systems B.V. 2023-11 | V01 | F.01U.408.367 User manual...
The Active profile follows the scheduled profiles under Recording Profiles. Please refer to section Recording Profiles. This behavior is only applicable when using Bosch recording solutions, including edge recording or VRM recording. Third-party recording solutions might use the Non-recording profile.
The Device manager indicates if storage is controlled locally or by a VRM system. An external Video Recording Manager (VRM) system for the unit is configured via the Configuration Manager. Bosch Security Systems B.V. 2023-11 | V01 | F.01U.408.367 User manual...
Page 36
Click a storage medium in the Managed storage media list to select it. Click Remove below the list. The storage medium is deactivated and removed from the list. 2023-11 | V01 | F.01U.408.367 Bosch Security Systems B.V. User manual...
Without metadata, it is not possible to include video content analytics in recordings. Select the mode for standard recordings: – Continuous: the recording proceeds continuously. If the maximum recording capacity is reached, older recordings are overwritten automatically. Bosch Security Systems B.V. 2023-11 | V01 | F.01U.408.367 User manual...
Enter the required retention time in days for each recording track. Once the storage unit is full, the previous recording will be overwritten. Click Set to apply the changes. 2023-11 | V01 | F.01U.408.367 Bosch Security Systems B.V. User manual...
Click Set to apply the changes. 5.5.5 Recording Status Details of the recording status are displayed here for information. These settings cannot be changed. Bosch Security Systems B.V. 2023-11 | V01 | F.01U.408.367 User manual...
Click Set to apply the changes. 5.5.8 SD Card Status This section identifies the details about the SD card installed in the device: – Manufacturer – Product – Size – State – Lifespan. 2023-11 | V01 | F.01U.408.367 Bosch Security Systems B.V. User manual...
– A warning through the Video Management System If a SD card is not installed, ‘SD card not found’ is shown. Notice! Bosch recommends the use of industrial micro SD cards with health monitoring. Alarm 5.6.1 Alarm Connections In the event of an alarm, the unit can automatically connect to a pre-defined IP address. The unit can contact up to ten IP addresses in the order listed until a connection is made.
Detection of movement can be used to trigger an alarm and to transmit metadata. Various VCA configurations can be selected and adapted to your application, as required. Configure the VCA setting in the Bosch Configuration Manager. 5.6.3 Alarm Email Alarm states can be documented by e-mail.
When finished, click Set to transmit the scripts to the device. If the transfer was successful, the message Script successfully parsed. is displayed over the text field. If it was not successful, an error message is displayed with further information. Bosch Security Systems B.V. 2023-11 | V01 | F.01U.408.367 User manual...
IP address of the gateway here. Otherwise, this field can remain empty (0.0.0.0). Additional addresses This section lists the IPv6 addresses available for use within the network. Ethernet The Ethernet options are defined in this section. 2023-11 | V01 | F.01U.408.367 Bosch Security Systems B.V. User manual...
Page 45
In UDP mode, comply with the MTU value set below. Network MTU [Byte] Specify a maximum value in bytes for the package size (including IP header) to optimize data transmission. Bosch Security Systems B.V. 2023-11 | V01 | F.01U.408.367 User manual...
Enter the appropriate IP address of the server. Server port (0 = Off) Enter the number of the server port. Protocol Select the appropriate protocol: UDP, TCP, or TLS. Click Set to apply the changes. 2023-11 | V01 | F.01U.408.367 Bosch Security Systems B.V. User manual...
QoS identifies the type of data in a data packet and divides the packets into traffic classes that can be prioritized for forwarding. Bosch Security Systems B.V. 2023-11 | V01 | F.01U.408.367 User manual...
Enter the port address for the stream here. Streaming Click the checkbox to activate multicast streaming mode. An activated stream is marked with a check. (Streaming is typically not required for standard multicast operation.) 2023-11 | V01 | F.01U.408.367 Bosch Security Systems B.V. User manual...
Do not interrupt the firmware installation. Even changing to another page or closing the browser window leads to interruption. Uploading the wrong files or interrupting the upload can result in the device no longer being addressable, requiring it to be replaced. Bosch Security Systems B.V. 2023-11 | V01 | F.01U.408.367 User manual...
To install or uninstall a license, type the respective key in the Activation key field and click Install or Uninstall. Alternatively, click License file to browse for license files and add them to the device. 2023-11 | V01 | F.01U.408.367 Bosch Security Systems B.V. User manual...
This function also protects the camera from unauthorized access. Debug Logging Retrieves detailed information of the active logs. Diagnostics This tab lists the individual diagnostics routines and their respective values. Reload Bosch Security Systems B.V. 2023-11 | V01 | F.01U.408.367 User manual...
This window is for information only and cannot be modified. Keep this information at hand when seeking technical support. Select the text on this page with a mouse and copy it so that it can be pasted into an e-mail if required. 2023-11 | V01 | F.01U.408.367 Bosch Security Systems B.V. User manual...
Search again for the IP address. Access the camera using the web browser. Set the initial password for the camera. Remove the camera bubble to access the reset button. Bosch Security Systems B.V. 2023-11 | V01 | F.01U.408.367 User manual...
– Repair & Exchange – Product Security Bosch Building Technologies Academy Visit the Bosch Building Technologies Academy website and have access to training courses, video tutorials and documents: www.boschsecurity.com/xc/en/support/training/ 2023-11 | V01 | F.01U.408.367 Bosch Security Systems B.V. User manual...
Need help?
Do you have a question about the FLEXIDOME micro 3100i NUV-3702-F02 and is the answer not in the manual?
Questions and answers