Subscribe to Our Youtube Channel
Related Manuals for WAREMA C 80 A8
Summary of Contents for WAREMA C 80 A8
- Page 1 WAREMA metal system venetian blinds Type C/E 80/90/93 A8 Instructions for use and maintenance To be handed over to the operator Valid from 20 July 2010 Document number [B867400_1] – EN...
-
Page 2: Table Of Contents
Table of contents Table of contents 1 Introduction ..........................3 Information on safety ..............................3 Information on the target group and application of these instructions ................ 3 Explanation of symbols and signs ..........................3 ... -
Page 3: Information On Safety
Failure e to comply with these instruc ctions relieve es WAREMA A of iability. Explan nation of sy ymbols and s signs rnings are ma arked with the ese symbols... -
Page 4: Introduction
Introduction Operating notes Important safety information The safety instructions and warnings described here are Product damage from operation of faulty intended to safeguard your health as well as protect the product! product. The following points must be read through carefully. Only operate external venetian blinds if they are in technically perfect condition. -
Page 5: Product Information
Product information Accessories Product information A wide range of control devices is available for our sun shading control systems to give you optimum control of Parts description the product. Do not use the external venetian blinds in icy or frosty weather. -
Page 6: Wind Speed Limits
Product informat tion e external ve enetian blinds will only me eet the require Wind d speed limi ents of the stat ted wind spee ed limits when mounted if: For external v enetian blinds s, the use of w wind speed lim mits ... -
Page 7: Operation
Operation Operation Operating the external venetian blind drive Operation with the crank Lowering using the sunblind push button/venetian blind switch Lowering/raising using the crank lower external Turn the crank clock- venetian blind: wise/anti-clockwise. Press "DOWN" Stop the venetian blind in button and hold if nec- any position: essary. -
Page 8: Operation Using The Central Control Unit
Operation Raising using the sunblind push button/venetian Incorrect operation blind switch Operation: general information/limiting access to the operating elements raise external venetian blind: Only operate Press the "UP" button external venetian blind and hold if necessary. if it is in technically perfect condition. -
Page 9: Care/Maintenance
Operation/care/maintenance Projection area: Risk of crushing/injury Care/maintenance Always keep General information on care and projection area of the maintenance external venetian blind clear of obstacles. Regular appropriate care and maintenance and the exclusive use of original spare parts are essential for ... -
Page 10: Care Instructions
Care/maintenance Clean the external venetian blind regularly (see Care instructions "Cleaning procedure" table). To do so, lower the ex- ternal venetian blind. To ensure the longest possible life, we recommend you clean the surface of the Cleaning procedure product regularly and at least once a year. Use suitable cleaning products on the surfac- If the first cleaning takes place years after initial installation, the product cannot be... -
Page 11: Maintenance Instructions
Check the screws of the tilt rod coupling to ensure The WAREMA guarantee becomes invalid if they are firmly seated. the unit is not cleaned properly at least once a year. -
Page 12: Warranty
To ensure that your product operates properly on a continuous basis and to avoid changing its approved status, use WAREMA spare parts only. Contact a qualified specialist for further information if necessary. [B867400_1] - EN / 20.07.11 Page 12 of 16... -
Page 13: Troubleshooting
Troubleshooting Troubleshooting CAUTION Injury or damage to persons or property resulting during troubleshooting! Problems with no reference to a qualified specialist or certified electrician may be rectified independently. Other problems are only to be dealt with by a qualified specialist or certified electri- cian. - Page 14 Troubleshooting Problem Possible causes Remedy Coupled blind reacts with a delay Slide the coupling piece into the tilt Coupling of tilt rod is missing or not at all rod coupling of the drive blind and tighten the locking screws (qualified specialists only).
- Page 15 [B867400_1] - EN / 20.07.11 Page 15 of 16 Subject to change without notice...
- Page 16 WAREMA Renkhoff SE Hans-Wilhelm-Renkhoff-Straße 2 97828 Marktheidenfeld, Germany www.warema.de info@warema.de...
Need help?
Do you have a question about the C 80 A8 and is the answer not in the manual?
Questions and answers