Advertisement
Wiring Diagram
P23
Voltage Out
Amperage Out +4-20mA
FEEDBACK OUT
GND(-)
Actuator Specifi cations
(+) 1-5, 0-5, 0-10vdc
Torque "lb/Nm
ALTERNATE SIGNAL IN
+4-20mA
Supply Voltage
SIGNAL IN
Max Inrush Current
(-)
Running Current
Motor
Runtime (90°@60Hz)
Runtime (90
@50Hz)
O
Duty Cycle
Motor Starts
Weight
Mechanical Connections
Electrical Entry
NOT OPEN*
Electrical Terminations
OPEN COM*
Environmental Rating
OPEN*
Manual Override
* CONNECTIONS
NOT CLOSED*
OPTIONAL
Control
CLOSED COM*
Actuator Case material
CLOSED*
Motor Protection
Ambient Temperature
Operating Range
L2 Neutral
120VAC 230VAC
L1 Hot
Neu
L2
GND
Hot
L1
GND GND
Field wiring and
devices by others
Torque Switches (if equipped)
For units equipped with torque switches:
Torque switches provide mechanical
overload protection for both the actuated
device and the geartrain.
These are factory set and are not
adjustable without proper equipment.
Torque switches are set to limit actuator
torque to approximately 105% of the
actuator rated output.
The wiring diagram above shows the
internal wiring connections between
the control board, the torque switches
and the motor. The upper torque switch
controls loading in the CW direction,
while the lower switch controls loading in
the CCW direction.
OTX-100
Actuator Specifi cations
7
Torque "lb/Nm
6
Supply Voltage
5
Max Inrush Current
Running Current
8 (+15v OUT)
P2
Motor
7
Runtime (90°@60Hz/vdc)
800"lbs/90Nm
1335"lbs/150Nm
6
Runtime (90
120vac
230vac
120vac
5
Duty Cycle
1.8A
0.8A
1.8A
4
Motor Starts
1.0A
0.5A
1.2A
3
Weight
Split Phase Capacitor
FEEDBACK OUT
Mechanical Connections
2
15 sec
Electrical Entry
WHT18
1
17 sec
DHC-100
Electrical Terminations
J2
ALTERNATE SIGNAL IN
25%, Proportional: Managed (75% maximum)
Environmental Rating
1200 per hour
SIGNAL IN
Manual Override
26lbs/12kg
Control
ISO5211 F07 F10 8pt 22mm
Actuator Case Material
(2) 3/4" NPT
12
12-16ga
Motor Protection
AUXILIARY
11
SWITCH
NEMA 4/4X
SW4
(STANDARD)
10
Ambient Temperature
5" Handwheel
Operating Range
9
On/Off -Jog, Proportional
AUXILIARY
8
Aluminum Alloy, Powder coated
SWITCH
SW3
(STANDARD)
230°F/110°C Thermal F* Class
7
*Totally Enclosed Non-Ventilated Motors
* CONNECTIONS
6
OPTIONAL
-22°F to +125°F
SW1
5
-30°C to +52°C
4
J1
SW2
3
E2
HEATER
E1
2
1
J3
J2
GND Screw
Items within dotted line indicates internal components
Actuator ships in fully closed position!
Use For:
P4/5/6-120DN4-ISOFB-TS
WARNING! Do NOT adjust the
torque switch cam settings.
This will VOID the warranty.
Actuator
Voltage
Amps
Wire
Gage
16
14
12
10
8
Page 4 of 18 P2-13 HV Proportion HR (-TS) Series
Proportional Control
120vac
P3
6
GRY
Close
POSITION
FEEDBACK
5
ORG
1K ohm
@50Hz)
O
4
230vac
BLU
OTX-101
WHT
1.2A
3
WHT18
1.0A
BLK
2
FACTORY
+4-20mA
CONNECTOR
BLU
1
(-)
J4
ISO F07 F10 22mm/Imp 3.5in BHCin ¾ X½ in
22 sec
J1
RED
26 sec
(+) 1-5, 0-5, 0-10vdc
+4-20mA
(-)
WHT18
J2
*Totally Enclosed Non-Ventilated Motors
NOT OPEN*
OPEN COM*
OPEN*
WHT
WHT
THERMAL
NOT CLOSED*
SWITCH
Capacitor
M
CLOSED COM*
CLOSED*
BLK
BLK
AC DRIVE
MOTOR
RED
ALL SWITCHES
SHOWN WITH
ACTUATOR IN
FULL OPEN
POSITION
L2 Neutral
GRN
L1 Hot
GND
Items within dotted line indicates internal components
Actuator ships in fully closed position!
Wire sizing data is provided in the table to
assist in the selection of the proper wire size for
ProMation actuators using various wire sizes
over distance.
Please make sure to reference the correct
voltage and do not exceed the indicated length
of the wire run for each model.
Wire Sizing Chart
MAX distance between Actuator and Supply (feet)
P2
120VAC
230VAC
1.8A
0.8A
722
3111
1166
5026
1783
7687
3030
13068
4523
19505
P2
800"lbs/90Nm
1335"lbs/150Nm
230vac
120vac
1.8A
0.8A
1.8A
1.3A
0.5A
1.3A
Split Phase Capacitor
15 sec
22 sec
17 sec
26 sec
Managed (75% maximum)
1200 per hour
+
26lbs/12kg
-
8 (+15v OUT)
(2) ISO ¾" / Imp ½" NPT
6
GRY
7
Close
5
12-16ga
ORG
6
4
NEMA 4/4X/IP67
BLU
5
WHT
3
5" Handwheel
4
BLK
2
3
Proportional
BLU
1
2
Aluminum Alloy, Powder coated
J1
RED
1
230°F/110°C Thermal F* Class
DHC-100
-22°F to +125°F
-30°C to +52°C
12
AUXILIARY
11
SWITCH
SW4
(STANDARD)
10
9
AUXILIARY
8
SWITCH
SW3
(STANDARD)
7
Gry
Gry
6
TSU
SW1
Capacitor
5
Blu
Blu
4
TSL
J1
SW2
3
RED
This motor wiring shows
ALL SWITCHES
E2
E1
HEATER
2
SHOWN WITH
the wiring for the products
ACTUATOR IN
1
J3
FULL OPEN
J2
POSITION
equipped with the optional
GRN
Torque Switch (-TS).
GND Screw
P3
120VAC
1.8A
722
1166
1783
3030
4523
P3
230vac
1.2A
0.5A
POSITION
FEEDBACK
1K ohm
FACTORY
CONNECTOR
J4
WHT
THERMAL
SWITCH
M
BLK
AC DRIVE
MOTOR
230VAC
1.2A
2074
3351
5125
8712
13003
Advertisement
