Front Panel Facilities - Pioneer VSX-9500S Operating Instructions Manual

FRONT PANEL FACILITIES
@ POWER STANDBY/ON switch
ON: The power to the unit is turned on.
still feeds the unit.
* The accessory remote control unit can also be used to turn the receiver
on or standby {STANDBY function).
NOTE,
® When not using the unit for along period, disconnect the power cord
from the AC OUTLETS in the wall.
© When the power is initially tarned ON, muting is applied to prevent
sound from being output far about 5 seconds.
@) SPLIT SCREEN control
This split screen function can be used when the ENHANCER switch
is on.
This contro! allows you to freely control the area of enhanced picture
(on right side of screen} and original picture (non-enhanced, on left side
of screen) by means of a vertical line dividing the screen into two
sections. It has no effect on an S output jack signal
Screen to which
enhancer has not
been applied
Screen to which
enhancer has
been applied
SPLIT SCREEN SPLIT SCREEN
Knob positions
SPLIT SCREEN
NOTE:
This line is not output from the VCR (VCR 1 and VCR 2) VIDEO OUT
jacks. As a result, the split screen image is not recorded, the recorded
image will be entirely that produced by the enhancer function
(3) ENHANCER control
When performing tape copying with a VCR, some deterioration in image
quality occurs normally. This contro! allows compensation for this
deterioration in image quality by emphasizing image detail. This has no
effect on an S output jack signal.
NOTE:
The ENHANCER control functions to suppress image deterioration, but
will not improve image quality beyond its original state.
@ ENHANCER switch
Press when performing video copying with added video enhancer
effects. When the switch is pressed, the monitored video image will
be the split screen picture.
Using the SPLIT SCREEN function will enable you to compare the
enhanced and original (non enhanced) images. It has no effect on an
S output jack signal.
The ENHANCER switch will not operate if the VCR 1 REC ENHANCER
is on (ENHANCER REC indication is lit} while the VCR 1 REC SEL switch
is on.
Turn off the VCR 1 REC SEL switch if you want to enhance the signal
sent to the MONITOR TV and RF MODULATOR jacks.
© VCR 1 REC ENHANCER switch
Turn this switch ON to record on the VCR connected to the VCR 1 jacks
the video image from VCR 2 or VDP with enhancement applied using
the ENHANCER control knob. At this time, the enhancer is turned off
for the monitor and VCR 2 REC OUT. This has no effect on an S output
jack signal.
NOTE:
° The VCR 1 REC SEL switch must be on for the VCR 7 REC
ENHANCER switch to operate.
26
<ARB1173>
(©) PRO LOGIC CENTER MODE switch (VSX-95008)
This operates if DOLBY PRO LOGIC SURROUND is ON. Switches
between the four DOLBY PRO LOGIC SURROUND center channel
settings. The setting changes in the order listed below each time you
press the switch.
NORMAL Use this setting whon a smali enclosure center
channel speaker incapable of reproducing frequencies
below 100Hz is connected,
WIDE —————— Use this setting when a large enclosure center
channel speaker capable of reproducing frequencies
below 100H7z is connected.
PHANTOM-—— Use this setting when no center channel speaker is
connected.
OFF —-—————. Select this setting for adjusting input balance. Use
a mono [AM radio, etc.| signal and adjust the
surround balance control on rear panel so that
volume is minimized from all speakers.
NOTES.
* Hf no center speaker is used, then mono signals and center channel
signal components will not be reproduced at positions other than the
PHANTOM position.
* To provide for correct surround operation, you must have a stereo
source or no output will be heard.
(7) PRO LOGIC TEST TONE switch (VSX-9500S)
Only operates when the DOLBY PRO LOGIC SURROUND surround
mode is selected. When the switch is turned ON, '"'TEST'' appears on
the central display and a test tone approximately two seconds in
duration is generated in all channels in succession. Adjust the speaker
level controls so that all speakers sound equally loud from the listening
position for the optimum surround effect. (See page 31.)
NOTE {For VSX-75008S only}:
Adjust the center speaker volume level of the amplifier driving the center
speaker, if one such amplifier) is used,
(8) VIDEO ADAPTOR switch
Press when using a video adaptor component connected to the rear
panel VIDEO ADAPTOR terminals. An indicator on the display section
lights up when this switch is set to ON, This has no effect on an S output
jack signal.
@) Audio/Video INPUT SELECTOR switches
VCR 1: Press when performing playback on a VCR unit.
VCR 2: Press when performing playback on a second VCR unit.
VCR 3: Press when performing playback on a third VCR unit.
VDP/CDV: Press when performing playback on a video disc player (VDP)
or CDV player.
TV: Press to watch TV broadcasts from the TV tuner connected to the
tear panel TV jacks.
VIDEO: Press when performing playback on a VCR connected to VIDEO
jack.
TAPE 1/DAT: Press when performing playback on a DAT or cassette
deck.
TAPE 2 MONITOR: Press when performing playback on a second
cassette deck and when monitoring recording or using a graphic
equalizer.
LINE: Press when performing playback on an audio component
connected to the LINE jacks.
CD: Press when playing compact discs on a CD player.
TUNER: Press when listening to radio broadcasts.
PHONO: Press when playing records on a turntable.
@® BAND selector switches
FM: Press for FM reception.
AM: Press for AM reception.
@ BALANCE switches
Use to adjust the sound volume balance between left and right speakers.
L: Press to decrease the sound on the right side.
R: Press to decrease the sound on the left side.
Press L and R together to bring the volume balance back to standard
(eft = Right).