Installation - Scheppach HP1800S Translation Of Original Instruction Manual

10. Installation

m ATTENTION!
Always make sure the device is fully assembled
before start-up!
Hand Grip (2), (fig. A)
When operating the compactor, use this hand grip (2)
to maneuver the compactor.
Throttle Control (1) (fig. A + C)
The throttle lever (1) controls engine speed. Moving the
throttle lever (1) in the directions shown makes the en-
gine run faster or slower.
fast =
langsam schnell
slow = langsam
vitesse lente vitesse rapide
Lift Point (3) (fig. A)
vitesse lente
slow fast
Used to lift the machine with crane or other lifting de-
vice.
slow
Pomalu rychle
Belt Guard (19) (fig. A)
Pomalu
Pomalý rýchly
Remove this guard (19) to gain access to the V-belt.
Never run the compactor without the V-belt guard (19).
Pomalý
hitrega
Počasnega
If the V-belt guard (19) is not installed, the possibili-
ty exists that your hand may get caught between the
Počasnega
lassú gyors
V-belt and clutch, thus causing serious injury and bod-
ily harm.
lassú
бавно бързо
Exciter (5) (fig. A)
бавно
Nopea hidas
An eccentric weight mounted on the exciter shaft con-
tained within exciter housing is driven at high speed by
Nopea
a clutch and belt drive system. This high speed shaft
revolution causes the rapid lifting and downward ram-
ming motion of the machine as well as imparting a for-
ward motion.
Engine switch (On-Off) (17) (fig. A + I)
The engine switch (17) enables and disables the igni-
tion system. The engine switch (17) must be in the ON
position for the engine to run.
Turning the engine switch (17) to the OFF position
stops the engine.
Check before operation
Check
• Look around and underneath the engine for signs of
oil or gasoline leaks.
• Look for signs of damage.
schnell
vitesse rapide
fast
rychle
rýchly
hitrega
gyors
бързо
hidas
www.scheppach.com
• Check that all shields and covers are in place, and
all nuts, bolts, and screws are tightened.
Checking the engine oil (fig. I -R)
• Take the oil dipstick (16) and clean.
• Insert the oil dipstick (16) in and check the oil lever
without screwing down.
• If the oil is too low, add the recommenced oil in.
• After finishing, reassemble and screw the oil dipstick
(16) down.
Check fuel (fig. S)
• First stop the engine, open the fuel cover (12), and
check oil level. If the oil level is too low, add the fuel
to full, after finishing, screw the fuel cover down.
• Don't add the fuel over the shoulder of the carburet-
tor when fuelling (maximum oil level).
• Recommended octane rating over 90 unleaded
gasoline For unleaded gasoline, can make carbon
deposit muck less and enhance exhaust system ser-
vice life.
• Don't use used and contaminated or gasoline with
oil , Avoid the dirt and water entering into fuel tank.
Starting engine (fig. I + K)
• Move the fuel valve lever (11) to the ON position.
To start a cold engine, move the choke (10) to the
CLOSE position
• If the choke lever (10) has been moved to the CLOSE
position to start the engine, gradually move it to
the OPEN position as the engine warms up.
• To restart a warm engine, leave the choke lever (10)
in the OPEN position.
• Turn the engine switch (17) to the ON position.
• Operate the recoil starter (14).
Recoil starter (5), (fig. A)
Pull the starter grip (14) lightly until you feel resistance,
then pull briskly, return the starter grip (14) gently. If
the choke lever (10) has been moved to the CLOSE
position to start the engine, gradually move it to
the OPEN position as the engine warms up. After
engine warms up, pull throttle lever (1) to accelerate
engine speed. Plate will begin vibrating and proceed
with compacting.
Forward motion
The plate compactor moves forwards automatically
when the throttle is opened fully.
GB | 31