Related Manuals for IBEX TM60
Summary of Contents for IBEX TM60
- Page 1 MANUAL OF USE AND MAINTENANCE ROTARY HARROW TM60 TM60-EN-R2021.01 Manual of use and maintenance: TM60...
- Page 2 PREFACE This manual is an integral part of the machine. It must always accompany the machine and be kept within reach of the operator. The enclosures mentioned are on integral part of this manual. The purpose of this manual. This manual gives information for the correct and safe use of the machine. The owner must read this manual carefully before work with the machine.
-
Page 3: Performance Limits
DESCRIPTION UNCTION OF USE The machine carries out all the function related with tools rotation in various work environment (open field, vineyards, orchards, flower gardens, parks, vegetable gardens), in all type of ground whatever its composition (sandy soil, medium mixture, clay) and consistency (crumbly, hard, semi-plastic) may be. The use of a technical constructive concept trended to the search of high performances, reduction of troubles and durability, improves the power/consumption ratio of the tractor thanks to the elasticity of the machine frame, to the tools shape and to many original technical solutions. -
Page 4: Technical Specifications
TECHNICAL SPECIFICATIONS HARACTERISTICS FOR MODEL Model Type Power Working width Weight Maximum working Total width N° of tools depth inch lbs. inch inch n° n° rotors teeth 30-50 22-38 248 546 60,9 TM60... -
Page 5: Safety Information
SAFETY INFORMATION ENERAL REGULATIONS Only work in daylight. The machine must not be used near people, especially children or animals. Wear long pants and heavy shoes. The protections are integral part of the machine: always work with the protections. ... - Page 6 SAFETY SIGNS ON THE MACHINE In this section, the safety signs on the machine are reproduced and explained. 1. Read the operator manual. 2. Disconnect the tractor key before maintenance and repair operations. 3. Stay at safety distance from PTO shaft. 4.
-
Page 7: Before Beginning Work
INSTRUCTIONS FOR USE EFORE BEGINNING WORK a) Connect the machine to the tractor as follows: 1. Insert the lifting arms of the tractor in the lower attachment points of the machine, lock by safety pin. 2. Connect the tractor linkage to the 3°-point hitch of the machine (triangle vertex), insert the pin and lock with safety pin. - Page 8 PROFESSIONAL SEEDER EEDER SET UP To empty the hopper, move lever “4” from position “C” to position “A”. After discharge of all seed move again lever “4” to position “C”. Fill the hopper with seed, now it is necessary to make set up of the machine considering how many Kg of seed you want to sow each hectare.
- Page 9 To verify weight in Kg that will be sow (generally the weight in Kg per hectare related to each type of seed is showed on technical sheet of the seed) operate as follow: Picture 1 Picture 2 Model Wheel turns Factor K Lift the seeder till the two wheels “W”...
-
Page 10: Grass Seeder
GRASS SEEDER EEDER ADJUSTMENT a. Fill the hopper with the seed then close the cover. b. To set the quantity of seed that will fall. operate as follow: 1. Move the latch knob "A" in the desired position. 2. Rise the lock knob placed on the upper part of the lever "B" then turn the lever clockwise to increase the quantity of seed that will fall, turn counter clock wise do decrease. - Page 11 MAINTENANCE INSTRUCTIONS On diagram "A" the maintenances are indicated with their terms to effect on the machine. Not follow the scheduled terms can compromise the functionality of the machine and in this case the warranty is not applicable. IAGRAM "A" SCHEDULED MAINTENANCE AFTER FIRST EVERY...
-
Page 12: Oil Level - Oil Replacement In Gearbox
GREASING At the scheduled time on diagram “A”, grease point “B”. Greasing point is equipped with greaser HYDRAULIC TYPE MODEL "A" UNI 7663. To greasing use only MULTIFUNCTIONAL GREASE LITHIUM BASED Type NLGI 2. IL LEVEL – OIL REPLACEMENT IN GEARBOX At the scheduled time on diagram “A”... -
Page 13: Tools Replacement
b) To replace oil in the transmission, operate as follows: 1. Unscrew the plug “B”, turn backward the machine and drain completely oil. 2. Introduce the new oil through the hole “B” up to oil touches lower hole rim. 3. When level is ok, lock the plug “B”. OOLS REPLACEMENT a) To replace the tools, operate as follows: 1. -
Page 14: Problems Solving
PROBLEMS SOLVING TROUBLES CAUSES AND SOLUTIONS -Decrease the forwarding speed Insufficient working depth -Tools are not sharpened or damaged -Broken or damaged tools Tools don’t penetrate -Check the tools assembling -Foreign objects between hoes - clean -Decrease the forwarding speed Rotary harrow bounces on the round and vibrates -Soil too dry and hard -Soil too wet... -
Page 15: Information On Demolition
TRANSPORT Except when working, moving the machine takes place when the machine is standing still and the transmission is disconnected. <Important>: keep speed low avoiding holes and ground roughness. <Note> when on the road, obey existing traffic laws. Exhibit the signal signs on the rear ends. Respect any local laws there may be. - Page 16 WORK AND MAINTENANCE SHEET Every user should register on this sheet the facts about the life of the machine (both work and maintenance), so as to attest its conditions. DATE WORKING MAITENANCE NOTE USER HOURS...
-
Page 17: Spare Part And Accessories
SPARE PART AND ACCESSORIES... - Page 18 TM60 MECHANISMS...
- Page 19 TM60 SHEETS...
- Page 20 TM60 LEVELLING BLADE...
- Page 21 TM60 ROLLER LIFTING TM60 WIRE ROLLER...
- Page 22 TM60 CAGE ROLLER TM60 SPIKED ROLLER...
- Page 23 SEEDER HOLDER...
-
Page 24: Spare Parts List Rotex
SPARE PARTS LIST ROTEX\ Quantity Code Description 42000002 GEARBOX 42400008 UCFC 206 SUPPORT 42400009 UCFC 208 SUPPORT 41000038 BEARING 6307 41000039 BEARING 6208 41100013 OIL SEAL 80x45x10 41200008 ORING 330 ERP165D SEAL ERP166D SEAL ERP164D SEAL 40400003 SEEGER Ø80 UNI 7437 41900005 SAFETY PROTECTION ERP062VD... - Page 25 Quantity Code Description ERP072EVD SPIKED ROLLER 170 ERP080VD LEFT SUPPORT SCRAPERS ERP081VD RIGHT SUPPORT SCRAPERS ERP433VD SCRAPERS PLATE ERP434DVD SCRAPERS BEAM 150 ERP431ZD SCRAPER ERP564D ROLL STOPPER 40100197 SCREW M10x45 UNI5739 40300003 WASHER Ø10 UNI 6592 40100102 SCREW M12x50 UNI 5737 40300004 WASHER Ø12 UNI 6592 40100229...
- Page 26 Quantity Code Description SRM205ZD SPACER ≠ 13x25x35 SRM204ZD SPACER ≠ 6x25x35 SRM203ZD SPACER PLASTIC PIPE 43000018 HOSE CLAMP 32-50 42500030 PLUG 50x50 42900001 RUBBER WHEEL Ø210x80 40800011 CHAIN ASA 41S ½” 67 LINK + JOINT 42300007 ELASTIC PIN 6x40 UNI 6873 40200002 NUT CONELOCK M8 DIN 980 40200059...
- Page 27 SEEDER PROFESSIONAL FRAME...
- Page 28 SEEDER PROFESSIONAL MECHANISM...
- Page 29 SEEDER GRASS - MECHANISM...
- Page 30 SEEDER GRASS - SHEET...
- Page 31 SEEDER GRASS - ATTACHMENT SEEDER GRASS - WIRE ROLLER...
- Page 32 INFORMATION ON DEMOLITION ......................... 15 WARRANTY ..............................15 WORK AND MAINTENANCE SHEET ......................16 TM60 MECHANISMS ............................18 TM60 SHEETS ..............................19 TM60 LEVELLING BLADE ..........................20 TM60 ROLLER LIFTING ..........................21 TM60 WIRE ROLLER ............................. 21 TM60 CAGE ROLLER ............................ 22...
- Page 33 TM60 SPIKED ROLLER ..........................22 SEEDER HOLDER ............................23 SPARE PARTS LIST ROTEX\ ........................24 SEEDER PROFESSIONAL FRAME ....................... 27 SEEDER PROFESSIONAL MECHANISM ..................... 28 SEEDER GRASS - MECHANISM ........................29 SEEDER GRASS - SHEET ..........................30 SEEDER GRASS - ATTACHMENT ........................ 31...