Related Manuals for IBEX TX40
Summary of Contents for IBEX TX40
- Page 1 Operators Manual Ibex Power Harrows Model: TX40 and TS52 Ibex TX40 Power Harrow with Mesh Roller & Leveling Blade ibexequipment.com 833-888-IBEX 2021-10...
- Page 2 PREFACE This manual is an integral part of the machine. It must always accompany the machine and be kept within reach of the operator. The enclosures mentioned are on integral part of this manual. The purpose of this manual. This manual gives information for the correct and safe use of the machine. The owner must read this manual carefully before work with the machine.
- Page 3 DESCRIPTION FUNCTION OF USE The machine, thanks to the large range of types models and versions all configurable through many available variants according to specific requirement, carries out all the function related with tools rotation in various work environment (open field, vineyards, orchards, flower gardens, parks, vegetable gardens), in all type of ground whatever its composition (sandy soil, medium mixture, clay) and consistency (crumbly, hard, semi-plastic) may be.
-
Page 4: Techinical Specifications
TECHINICAL SPECIFICATIONS CHARACTERISTICS FOR MODEL Model Type Power Working width Weight Maximum working Total width N° of tools depth inch lbs. inch inch n° n° rotors teeth 12-25 13-26 127 280 12-25 15-30 145 320 ROTEX-L 12-25 18-33 160 353 12-25 22-38 170 375... -
Page 5: Safety Information
SAFETY INFORMATION ENERAL REGULATIONS Only work in daylight. To prevent damage due to lunch of objects or parts of blades, before to start job be sure that any persons or animals should be in the radius of 50 meters from the machine. ... -
Page 6: Safety Signs On The Machine
SAFETY SIGNS ON THE MACHINE In this section, the safety signs on the machine are reproduced and explained. 1. Read the operator manual. 2. Disconnect the tractor key before maintenance and repair operations. 3. Stay at safety distance from PTO shaft. 4. -
Page 7: Before Beginning Work
INSTRUCTIONS FOR USE EFORE BEGINNING WORK a) Connect the machine to the tractor as follows : 1. Insert the lifting arms of the tractor in the lower attachment points of the machine, lock by safety pin. 2. Connect the tractor linkage to the 3° point hitch of the machine (triangle vertex), insert the pin and lock with safety pin. - Page 8 SEEDER ADJUSTMENT a. Fill the hopper with the seed then close the cover. b. To set the quantity of seed that will fall. operate as follow : 1. Move the latch knob "A" in the desired position. 2. Rise the lock knob placed on the upper part of the lever "B" then turn the lever clock wise to increase the quantity of seed that will fall, turn counter clock wise do decrease.
- Page 9 MAINTENANCE INSTRUCTIONS On diagram "A" the maintenances are indicated with their terms to effect on the machine. Not follow the scheduled terms can compromise the functionality of the machine and in this case the warranty is not applicable. IAGRAM "A" SCHEDULED MAINTENANCE AFTER FIRST EVERY...
-
Page 10: Oil Level - Oil Replacement In Gearbox
GREASING At the scheduled time on diagram “A”, grease point “A”. Greasing point is equipped with greaser HYDRAULIC TYPE MODEL "A" UNI 7663. To greasing use only MULTIFUNCTIONAL GREASE LITHIUM BASED Type NLGI 2. OIL LEVEL – OIL REPLACEMENT IN GEARBOX At the scheduled time on diagram “A”... -
Page 11: Tools Replacement
c) To check the oil in the transmission, operate as follows: 1. With the machine on level unscrew the plug "B" and check that oil touches lower hole rim. 2. If the level is ok, lock the plug "B". 3. If the level is low, fill oil. 4. -
Page 12: Problems Solving
PROBLEMS SOLVING TROUBLES CAUSES AND SOLUTIONS -Decrease the forwarding speed Insufficient working depth -Tools are not sharpened or damaged -Broken or damaged tools Tools don’t penetrate -Check the tools assembling -Foreign objects between hoes - clean Rotary harrow bounces on the round and -Decrease the forwarding speed vibrates -Soil too dry and hard... -
Page 13: Information On Demolition
TRANSPORT Except when working, moving the machine takes place when the machine is standing still and the transmission is disconnected. <Important>: keep speed low avoiding holes and ground roughness. <Note> when on the road, obey existing traffic laws. Exhibit the signal signs on the rear ends. Respect any local laws there may be. - Page 14 WORK AND MAINTENANCE SHEET Every user should register on this sheet the facts about the life of the machine (both work and maintenance), so as to attest its conditions. DATE WORKING MAITENANCE NOTE USER HOURS...
-
Page 15: Spare Part And Accessories
SPARE PART AND ACCESSORIES... - Page 16 ROTEX MECHANISMS...
- Page 17 ROTEX-L SHEET...
- Page 18 LEVELLING BLADE ROTEX-L...
- Page 19 ROTEX-L WIRE ROLLER...
- Page 20 ROTEX-L CAGE ROLLER...
- Page 21 Quantity Code Description ERP100AVD COVER ERP100BVD COVER ERP100CVD COVER ERP100DVD COVER ERP101AVD MAIN FRAME ERP101BVD MAIN FRAME ERP101CVD MAIN FRAME ERP101DVD MAIN FRAME ERP102VD III° POINT HITCH ERP506VD RIGHT GEAR BOX SUPPORT ERP507VD LEFT GEAR BOX SUPPORT ERP508VD GEAR BOX COVER ERP103VD SUPPORT ERP322VD...
- Page 22 Quantity Code Description 41000065 BEARING 22205 CC 42400008 MIDDLE SUPPORT UCF 206 42400012 SIDE SUPPORT UCF 204 42400006 ROLL SUPPORT UCFL 205 41100037 SEAL 52x40x7 41200009 OR 3100 ERP539D HUB SEAL ERP166D MIDDLE SUPPORT SEAL ERP540D SIDE SUPPORT SEAL 42500038 COVER SEAL 42500039 COVER SEAL...
- Page 23 SEEDER GRASS - MECHANISM...
- Page 24 SEEDER GRASS - SHEET...
- Page 25 SEEDER GRASS - ATTACHMENT...
- Page 26 INDEX PREFACE ..................................2 DESCRIPTION ................................3 FUNCTION OF USE ..............................3 PERFORMANCES ..............................3 PERFORMANCE LIMITS ............................3 STANDARD .............................. 3 FEATURES VARIANT & ACCESSORI ............................ 3 TECHINICAL SPECIFICATIONS ..........................4 SAFETY INFORMATION ............................. 5 GENERAL REGULATIONS ............................5 SAFETY RESTRICTIONS ............................