Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Flamerite Fires E-FX SL
Summary of Contents for Flamerite Fires E-FX SL
- Page 1 INSTALLATION, PRECAUTIONS & SERVICING E-FX SL & E-FX SL Lite...
-
Page 2: Table Of Contents
IMPORTANT INFORMATION CONTENTS • • Please bear in mind the weight of the The accessories are found in a box Important Information ..............................4 fire before removing from the packaging that is packed at the side of the fire. UKCA & CE Declarations ............................7 and installation. - Page 3 IMPORTANT INSTRUCTIONS IMPORTANT INSTRUCTIONS • • Cleaning and user maintenance shall NOT Extreme caution is necessary when any be made by children without supervision. heater is used by or near children or invalids and whenever the heater is left • Children of less than 3 years should be operating and unattended.
-
Page 4: Ukca & Ce Declarations
IMPORTANT INSTRUCTIONS UKCA & CE DECLARATIONS TRADE NAME RATINGS PRODUCT TYPE MANUFACTURED BY Flamerite Fires LTD. Greenhough Road, E-FX 220-240 Vac, 50Hz Class I Electric Fire (fan heater) Lichfield. Staffs. WS13 7AU. United Kingdom. CAUTION REQUIREMENTS: BS-EN 60335-2-30:2009 + A11:2012... -
Page 5: Etl Declarations
ETL DECLARATIONS TECHNICAL SPECIFICATIONS TRADE NAME RATINGS PRODUCT TYPE MANUFACTURED BY Flamerite Fires LTD. Greenhough Road, E-FX 120 Vac, 60Hz Class I Electric Fire (fan heater) Lichfield. Staffs. WS13 7AU. United Kingdom. REQUIREMENTS: UL 2021 & CAN/CSA E60335-2-30 CERTIFICATE NUMBER... -
Page 6: Required Tools
REQUIRED TOOLS WHAT’S IN THE BOX... HAMMER & HEX KEY SCREWDRIVER E-FX FIRE LOG SET FRONT GLASS DRILL & TAPE MEASURE ACCESSORY & INSTRUCTIONS & DRILL BITS POWER LEAD HARDWIRE PACK WARRANTY CARDS REMOTE & GLASS HANDLE FIXING PACK BATTERIES PENCIL SPIRIT LEVEL E L E C T R I C F I R E S M A D E I N E U R O P E... -
Page 7: Before You Start
BEFORE YOU START... FLAT WALL INSTALLATION PLUG SOCKETS & WALL CONSTRUCTION All fires must have an accessible plug. Do not fit a fire above a socket. Building regulations require Start by building the framework for the wall. The sizes are listed in a the table below for your fire. the socket to be located at the side of the unit. - Page 8 FLAT WALL INSTALLATION FLAT WALL INSTALLATION Now the framework and sockets are installed, you can fix your fire to the frame. Be sure you plug Now the fire is installed, you can fix the panels the wall. Make sure everything is working before anything in before you start to add any panel work.
-
Page 9: Rear Screen Options
FLAT WALL INSTALLATION REAR SCREEN OPTIONS STANDARD E-FX Screw the panelling to the framework and make sure everything lines up and is working. We reccomend using 15-18mm finishing boards. This is so you can apply any finishes such as plaster As standard one of the two rear screens in the E-FX fire has a reflective coating to mirror coatings or decorative panelling. -
Page 10: Hardwire Installation
HARDWIRE INSTALLATION REAR SCREEN OPTIONS Using the glass sucker provided, WARNING! remove the rear glass. Leave the projection screen in place. You can Before any wiring work is undertaken, make sure the then reconnect the fuelbed and screw power for the socket has been turned off at the fuse box it back into place. - Page 11 HARDWIRE INSTALLATION HARDWIRE INSTALLATION Fit the fused spur socket leaving enough power cable to get to the fire, leaving plenty of wire to Disconnect the current power bracket, found trim back. on the right inside the fire. Remove the terminals from the power inlet and unscrew the bracket from the fire.
- Page 12 HARDWIRE INSTALLATION HARDWIRE INSTALLATION Now trim the fire power cables by removing the terminals and leave 13mm of cable exposed to Now the mains cables are connected, connect the fire by inserted the trimmed cables into the connect the mains supply. The Neutral gray cable is a twin cable. corresponding connector.
-
Page 13: Front Glass Installation
HARDWIRE INSTALLATION FRONT GLASS INSTALLATION Before reinstalling the fuel bed, remove the cable clip from the hardwire bracket and use it to To Install the front glass, first secure the mains cable in place. This will ensure that nothing can be disconnected if the cable clean the glass with a soft is accidentally pulled, so make sure its on securely. -
Page 14: Informational Requirements
Room temperature control with open window detection: Yes Adaptive Start With electronic room temperature control plus week timer: Yes E-FX SL LITE E-FX SL LITE: INFORMATIONAL REQUIREMENTS FOR ELECTRIC LOCAL SPACE HEATERS Now the glass handle has been fitted, MODEL SL600 - 24”... -
Page 15: Maintenance & Cleaning
MAINTENANCE & CLEANING TROUBLE SHOOTING PROBLEM CAUSE SOLUTION Check lead in plugged in securely and p-clipped in place WARNING! Mains lead not plugged in (PAGE 17-23) NO POWER TO FIRE Circuit board Replacement part required (QUOTE PART NUMBER E50) Before any wiring work is undertaken, make sure the power for the socket has been turned off at the fuse box and check that Mains socket Check socket is switched on... -
Page 16: Wiring Diagram
TROUBLE SHOOTING WIRING DIAGRAM PROBLEM CAUSE SOLUTION Turn fire off & on using the rocker switch next to keypad Lost rf connection to fire and repair the remote. See App instructions. REMOTE CONTROL NON RESPONSIVE Batteries Replace with 2 x AAA Debris from fuel bed Remove debris in channel... -
Page 17: Parts List
PARTS LIST EXPLODED DIAGRAM E-FX E-FX LITE PART SL600 SL750S SL750T SL1000 SL600 SL750S SL750T SL1000 PART NAME NUMBER (24”) (30”) (30”) (40”) (24”) (30”) (30”) (40”) Power Lead E90-1 E90-1 E90-1 E90-1 E90-1 E90-1 E90-1 E90-1 Motor Spindle 280mm LED Patent Glass Rear Screen FE225... -
Page 18: Notes
NOTES NOTES E L E C T R I C F I R E S M A D E I N E U R O P E E L E C T R I C F I R E S M A D E I N E U R O P E... - Page 19 These products are only suitable for well insulated spaces or occasional use. Manufactured in the United Kingdom. All products are protected by patents, registered design and intellectual property rights. Flamerite Fires Ltd. will protect these rights. All specifications are correct at the time of publishing but are subject to change.
Need help?
Do you have a question about the E-FX SL and is the answer not in the manual?
Questions and answers