Related Manuals for CANADA BILLARD & BOWLING INC DIVINE
Summary of Contents for CANADA BILLARD & BOWLING INC DIVINE
- Page 1 DIVINE INSTALLATION MANUAL rev 2020-12-12 CANADA BILLIARD & BOWLING INC. 4050 Industriel blvd, Laval, QC, H7L 6C3 450-963-5060 W W W.CANADABIL LIARD.COM...
-
Page 2: Lifetime Guarantee
LIFETIME GUARANTEE CANADA BILLIARD is pleased to offer an unsurpassed LIFETIME GUARANTEE TO THE ORIGINAL PURCHASER against defects in material and workmanship, provided installation and/or service is performed by an Authorized Dealer or a factory-approved installer. Cloth, pockets and rail cushions are not covered under this guarantee. - Page 4 1 Place the legs stretcher up side down and place the (4) 2 Assemble the leg stretcher and legs base with hexagon wood dowels 1/2” x 2”. bolts 3/8”-16 x 3 1/2”” and flat washers 7/16”. 3 Install the second legs base. 4 Thighten the bolts.
- Page 5 7 Fasten the legs on legs base with (8) hexagon bolts 8 Tighten the bolts. 3/8” x 3 1/2” and flat washers 7/16”. 10 Turn the legs assembly. 9 Repeat for other legs. 11 Install the (4) wood dowel pins on legs. 12 Fasten the top legs stretcher to the legs with (8) hexagon bolts 3/8”-16 x 2 1/4”...
- Page 6 14 Screw the (8) threaded rods 3/8”-16 x 4 1/2”on top 13 Tighten the bolts. legs stretch 15 D Place end sills. 16 Screw the (8) threaded rods 3/8”-16 x 3” on side sills. 17 Install the (2) side sills, (2) end sills and the (2)frame 18 Fasten the side sills, end sills and the frame support supports.
- Page 7 19 Fasten the end sills to the side sills with flat washers 20 Fasten the two slate joint support sills to the frame 7/16” and hexagon nuts 3/8”-16. with hexagon bolts 3/8”-16 x 1 3/4” and flat washers 7/ 16 ”. 21 Fasten the center support to the two slate joint 22 Tighten all the bolts.
- Page 8 26 Assemble the frame to the legs assembly with flats 25 Place the frame on the legs assembly. washers 13/32” and hexagon nuts 3/8”-16 . Do not tig h ten. 27 Position the table in its permanent location. 28 With the (4) hexagon bolts 1/2”-13 level the frame 29 Check the level.
- Page 9 32 Push the end sections towards the middle section to 31 Center the middle slate on base frame. close any gap. 33 Fasten the slate with # 14 x 2 1/2” flat head screws. 34 Level the slate and put shims as needed. Adjust the joints so that both sections are perfectly levelled.
- Page 10 37 Spray adhesive on one side of strip of cloth and glue 38 Place the cloth over the slate with the tag «playing one to each pocket entry. surface» on top. 39 Staple 4” at center of one end of the table. 40 Pull lightly towards #2 and staple on #2.
- Page 11 43 Pulling towards #1, staple approx. 4”. Repeat for #2, 44 Strech and staple under the pocket cut out #1, #2, #3 #3 and #4. Cut 5 to 6 slits at the 4 corner pocket cut out. and #4. Stretch and staple all sides . Cut excess of cloth. 45 Locate rail attachment holes and cut a small hole in 46 Place the rails upside down on the table.
- Page 12 49 Assemble the rails. 50 Install the second part of counter bolts. 52 Screw the 3/8”-16 x 3” full threaded rods into the 51 Thighten the counter bolts. rails. 54 Fasten the corner apron to the aprons with (16) machine 53 Place the aprons on rails.
- Page 13 55 Thigthen the screws. 56 Screw the aprons on rails with (I 8) wood screws #8 x I 3/4 flat head. 57 Carefully tum the rail and apron assembly over. 58 Place the rail and apron assembly on table. 60 Place the pocket. 59 Secure the rails with 3/8"...
- Page 14 61 Nail the pocket. Make sure all the surface covers the r 62 Screw the leather pocket strips to the framed slate ails . with #7 x 1/2” round head screws. 63 Thigthen the end rails at the center of the table. Align and tighten all the side rails.
- Page 16 YOU ARE NOW READY TO PLAY YOUR FIRST GAME OF POOL ON YOUR MAGNIFICENT BILLIARD TABLE FROM CANADA BILLIARD ! CONGRATULATIONS ! CANADA BILLIARD & BOWLING INC. 4050 Industriel blvd, Laval, QC, H7L 6C3 450-963-5060 W W W.CANADABILLIARD.COM...