Related Manuals for CANADA BILLARD & BOWLING INC EURO
Summary of Contents for CANADA BILLARD & BOWLING INC EURO
- Page 1 CANADA BILLIARD & BOWLING INC. 4050 Industriel blvd, Laval, QC, H7L 6C3 450-963-5060 W W W.CANADABIL LIARD.COM...
-
Page 2: Lifetime Guarantee
LIFETIME GUARANTEE CANADA BILLIARD is pleased to offer an unsurpassed LIFETIME GUARANTEE TO THE ORIGINAL PURCHASER against defects in material and workmanship, provided installation and/or service is performed by an Authorized Dealer or a factory-approved installer. Cloth, pockets and rail cushions are not covered under this guarantee. - Page 3 #4 SLATE Wood screws #14 x 2 1/2" (flat head) #5 APRONS Corner brackets 3/4" x 3/4" x 2 1/2" Wood screws #7 x 1/2" (round head) MIS CE L L A NEOUS Angles Euro 16-06EURO Set of (6) pockets 16-115S...
- Page 4 1 According to the picture above, place the 2 Unwrap legs and unscrew hardware on a clean surface. leg levellers about 1/2". 3 Place on the ground, on a clean surface, the 4 legs, 4 Screw the threaded rods 3/8" x 4 1/2" the 4 frame pieces and the joint support sills.
- Page 5 7 On one of the assembled ends, install both 8 Install the 8 metal brackets using hexagon long frames. Lift and fix the other 3/8"-16 x 1" bolts and 7/16" flat washers. short frame assembly. Tighten all bolts. 9 Install the two joint support sills with 10 Install the short joint support sill 3/8"-16 x 1 3/4"...
- Page 6 13 Place the center slate over the base frame. 14 Push the end sections towards the middle section Center it on the base frame. Place the two end to close any gap. Level each section. sections matching the half-circle on the slate (A). 15 Pre-drill with a 5/32"...
- Page 7 19 Place the cloth over the slate with 20 Staple 4" on center of one end of the table. tag "playing surface" on top. 21 Pulling toward #2, staple on #2. Repeat for #3. 22 Pulling tightly toward #1, staple approx. 4". Pulling tightly toward #4, staple approx.
- Page 8 25 Pulling toward #1, staple approx. 4". Repeat for #2. 26 Cut 5 to 6 slits at the 4 corner pocket cuts out. Repeat for each of the corner pockets. Stretch and staple under the pocket cuts out. Repeat for each corner by stretching the cloth. 27 Stretch and staple all sides.
- Page 9 31 Tighten so that each seal 32 Insert a dowel per center pocket. corner is perfectly closed. Make sure to leave 1/16" between the end of the panel and the bracket. 33 Close the gap manually. 34 At the two ends of the two long aprons, on their inside, attach two brackets with two #7 wood screws.
- Page 10 When doing it, make sure that the center joint is securely closed (figure 33). 37 Place the other brackets on the side of the apron 38 Center the aprons on the rail and apron assembly. (2 per rails). Fix the panels on the rails using the brackets and the #7 x 1/2".
- Page 11 43 Adjust and cut side pockets as necessary. 44 Nail the pockets with included nails. YOU ARE NOW READY TO PLAY YOUR FIRST GAME OF POOL ON YOUR MAGNIFICENT BILLIARD TABLE FROM CANADA BILLIARD ! CONGRATULATIONS !
- Page 12 CANADA BILLIARD & BOWLING INC. 4050 Industriel blvd, Laval, QC, H7L 6C3 450-963-5060 W W W.CANADABILLIARD.COM...