Related Manuals for CANADA BILLARD & BOWLING INC REBEL
Summary of Contents for CANADA BILLARD & BOWLING INC REBEL
- Page 1 REBEL Installation manual 2021-03-20 CANADA BILLIARD & BOWLING INC. 4050 Industriel blvd, Laval, QC, H7L 6C3 450-963-5060 W W W.CANADABIL LIARD.COM...
-
Page 2: Lifetime Guarantee
LIFETIME GUARANTEE CANADA BILLIARD is pleased to offer an unsurpassed LIFETIME GUARANTEE TO THE ORIGINAL PURCHASER against defects in material and workmanship, provided installation and/or service is performed by an Authorized Dealer or a factory-approved installer. Cloth, pockets and rail cushions are not covered under this guarantee. - Page 4 1 Place the hardware on a clean surface. 2 Unwrap legs and unscrew leg levellers for about 1/4. 3 On a clean floor, place the long and short base Install on the short base frame 3/8"-16 x 4 1/2" frames. threaded rods and dowel pins.
- Page 5 8 Before fastening those legs, by pulling then up, be 7 Keeping the centre leg's levelers completely screwed. sure that the joints between the legs and the frames install them with 3/8"-16 x 4 1/2" hexagonal bolt and are close. At this point, the table must stand on it's 7/16"...
- Page 6 13 Unscrew the center leg levelers to the floor. 14 With help, dispose of the slate sections on the base frame. 15 Make sure to keep about 1" inbetween them. 16 Start by correctly positionning the center section. 17 Put together all the slate section 18 Check the proper leveling of each slate section.
- Page 7 20 If needed, use wedges and fill the joint with slate 19 Check the joints. joint wax,"plasco" ciment or light body filler. 22 Fix them underneath the slate using 2" wood screws 21 Pace the tacking strips on the table. #14.
- Page 8 25 Using a wood ripper, adjust corner's and side's 26 Cut 1 1/2" wide strip of cloth. Spray adhesive on tacking strips to the slate pocket openings. all pocket entries. Spray adhesive on one side of the cloth strips and glue one to each pocket entry. 27 Place the cloth over the slate with 28 Staple 4"...
- Page 9 31 Pulling toward #2, staple on #2. Repeat for #3. 32 Pulling tightly toward #1, staple approx. 4". Pulling tightly toward #4, staple approx. 4". Repeat for #2, #3 and #4. Repeat for #5 and #6. 33 Pulling toward #1, staple approx. 4". Repeat for #2. 34 Cut 5 to 6 slits at the 4 corner pocket cuts out.
- Page 10 37 Use counter bolts to 38 Place the dowels pins 5/8" x 2". Place assemble the rails. the A part in one of the holes and screw the B part into the A part. 39 Fasten the end rail #1 to the side rail #2. 40 Proceed the same way Place the C part on B rod and turn the for all rails.
- Page 11 44 Install 3/8"-16 x 3 3/4" threaded rods into the rails 43 Underneath the table, use the counter bolts the fix throught the slate holes. the the side rails assembly. 45 Install loosely 3/8" lockwashers and 3/8"-16 CAREFULLY put the sides aprons unside down on the hexagonal nuts.
- Page 12 49 Once all aprons are in place, sccrew the them 50 Align the side rails and onto the rails using #8 x 1 1/4" wood screws. tighten all the rails. 51 Nail the pockets. Make sure all the surface 52 Fasten the leather straps under the slate covers the rails.
- Page 14 YOU ARE NOW READY TO PLAY YOUR FIRST GAME OF SNOOKER ON YOUR MAGNIFICENT SNOOKER TABLE FROM CANADA BILLIARD ! CONGRATULATIONS ! CANADA BILLIARD & BOWLING INC. 4050 Industriel blvd, Laval, QC, H7L 6C3 450-963-5060 W W W.CANADABILLIARD.COM...