Subscribe to Our Youtube Channel
Related Manuals for CANADA BILLARD & BOWLING INC ONYX
Summary of Contents for CANADA BILLARD & BOWLING INC ONYX
- Page 1 ONYX / INDUSTRIA Installation manual SHACK / LA FORGE 2021-05-15 CANADA BILLIARD & BOWLING INC. 4050 Industriel blvd, Laval, QC, H7L 6C3 450-963-5060 W W W.CANADABIL LIARD.COM...
-
Page 2: Lifetime Guarantee
LIFETIME GUARANTEE CANADA BILLIARD is pleased to offer an unsurpassed LIFETIME GUARANTEE TO THE ORIGINAL PURCHASER against defects in material and workmanship, provided installation and/or service is performed by an Authorized Dealer or a factory-approved installer. Cloth, pockets and rail cushions are not covered under this guarantee. - Page 4 1 According to the picture above, 2 Unwrap legs and unscrew leg levellers place the hardware on a clean surface. for about 1/2". 4 To do so, use 3/8"-16 x 1" BLACK hexagonal bolt and 3 According to your table model, assemble the legs 7/16"...
- Page 5 127 the short frames using 3/8"-16 8 With 3/8"-16 x 1 3/4" hex bolts and hex nuts and 7/16" washers. 7/16" washers, slightly tighten the cross pieces of the legs with the long frames. 9 AWith 3/8"-16 x 1 3/4" bolts and 10 Loosely fasten the long cross pieces to the short 7/16"...
- Page 6 14 Tighten all bolts and nuts. 13 Fix with 3/8"-16 x 3" hexagonal bolts and 13/32 bumper washers and 3/8-16 hexagonal nuts.. 15 Find the highest corner. Adjust the level 16 Position the middle section of the slate of the table by unscrewing the levellers on the cross pieces and sills.
- Page 7 19 Pre-drill with a 5/32" dia. drill bit the fixing 20 Using the wedges, adjust joints so that the two slate and fix the 3 section slate in 12 points surfaces are equal. Unscrew and screw in as needed. with screws #14 2 1/2". Check the level.
- Page 8 25 Pulling toward #2, staple on #2. Repeat for #3. 26 Pulling tightly toward #1, staple approx. 4". Pulling tightly toward #4, staple approx. 4". Repeat for #2, #3 and #4. Repeat for #5 and #6. 27 Cut 5 to 6 slits on one of the center pockets. 28 Pull and staple under the slate frame.
- Page 9 31 Stretch and staple all sides. 32 Locate rail attachment holes and cut clearance Cut excess of cloth. on cloth with a sharp knife (approx. 1/2" dia). 33 Use counter bolts to 34 Place the dowels pins 5/8" x 2". Place assemble the rails.
- Page 10 37 Screw the 3/8"-16 x 3 full threaded 38 Put together the panels' frame rods into the rails. following the numeral order. 39 Assemble the frame using 1/4"-20 x 1 1/2" 40 Adjust and tighten machine screws and 5/16" flat washers. the screws.
- Page 11 43 Secure the rails with 3/8" tooth lock washers 44 Align the side rails and and 3/8"-16 hexagon nuts on threaded rods tighten all the rails. (make sure the nut is not cross-threated). 45 Nail the pockets. Make sure all the surface 46 Fasten the leather straps under the slate covers the rails.
- Page 12 CANADA BILLIARD & BOWLING INC. 4050 Industriel blvd, Laval, QC, H7L 6C3 450-963-5060 W W W.CANADABILLIARD.COM...
Need help?
Do you have a question about the ONYX and is the answer not in the manual?
Questions and answers