Related Manuals for CANADA BILLARD & BOWLING INC X-TREME
Summary of Contents for CANADA BILLARD & BOWLING INC X-TREME
- Page 1 X-TREME / CANYON INSTALLATION MANUAL 2020-08-12 CANADA BILLIARD & BOWLING INC. 4050 Industriel blvd, Laval, QC, H7L 6C3 450-963-5060 W W W.CANADABIL LIARD.COM...
-
Page 2: Lifetime Guarantee
LIFETIME GUARANTEE CANADA BILLIARD is pleased to offer an unsurpassed LIFETIME GUARANTEE TO THE ORIGINAL PURCHASER against defects in material and workmanship, provided installation and/or service is performed by an Authorized Dealer or a factory-approved installer. Cloth, pockets and rail cushions are not covered under this guarantee. - Page 4 2 On a clean surface, dispose of the "x" shaped legs, the 1 On a clean surface, dispose of the hardware. stretcher and the decorative nuts. 4 Make the threaded rod on one end of the stretcher 3 Carefully, make one leg stand. pass through the hole in the leg.
- Page 5 7 Place the decorative nuts on both end on the Tighten manually. stretcher. 10 Fix them in place with 3/8"-16 x 1 1/4" hexagonal 9 Place the upper members of the legs. bolts and 13/32 bumper washers. 12 Install the 3/8"-16 x 4 1/2" threaded rods on the 11 Tighten.
- Page 6 13 Install the 3/8"-16 x 3" threaded rods in both long 14 Slightly tighten both short base frame to one long one base frame. with 3/8"-16 hexagonal nuts and 7/16" flat washers. 15 Install the 1/2"-13 x 3" hexagonal bolts without 16 Assemble and slightly tight the base frame including making them exceed underneath the legs crossmembers the legs crossmembers.
- Page 7 19 Tighten the base frame assembly. 20 Tighten the legs crossmembers onto the long base frames. 22 Use 3/8"-16 hexagonal nuts keeping a 1/2" gap 21 Use 13/32 bumper washers. between nuts ans washers. 23 Slightly tighten both long crossmembers to the long 24 Slightly tighten the short crossmember to the long base frame.
- Page 8 25 Put your tool on the leg crossmember and on the 26 Level the frame by screwing and unscrewing the 1/2"- long base frame to adjust the level of the assembled base f 13 x 3" hexagonal bolts. r ame. 27 Fasten 3/8"-16 nuts to secure your base frame 28 Put your 3 piece slate on the leveled frame.
- Page 9 31 Pre-drill with a 5/32" dia. drill bit the fixing 32 Using the wedges, adjust joints so that the two slate and fix the 3 section slate in 12 points surfaces are equal. Unscrew and screw in as needed. with screws #14 2 1/2". Check the level.
- Page 10 37 Pulling toward #2, staple on #2. Repeat for #3. 38 Pulling tightly toward #1, staple approx. 4". Pulling tightly toward #4, staple approx. 4". Repeat for #2, #3 and #4. Repeat for #5 and #6. 39 Cut 5 to 6 slits on one of the center pockets. 40 Pull and staple under the slate frame.
- Page 11 43 Stretch and staple all sides. 44 Locate rail attachment holes and cut clearance Cut excess of cloth. on cloth with a sharp knife (approx. 1/2" dia). 45 Use counter bolts to 46 Place the dowels pins 5/8" x 2". Place assemble the rails.
- Page 12 49 Screw the 3/8"-16 x 3 full threaded 50 Put together the panels' frame rods into the rails. following the numeral order. 51 Assemble the frame using 1/4"-20 x 1 1/2" 52 Adjust and tighten machine screws and 5/16" flat washers. the screws.
- Page 13 55 Secure the rails with 3/8" tooth lock washers 56 Align the side rails and and 3/8"-16 hexagon nuts on threaded rods tighten all the rails. (make sure the nut is not cross-threated). 57 Nail the pockets. Make sure all the surface 58 Fasten the leather straps under the slate covers the rails.
- Page 14 CANADA BILLIARD & BOWLING INC. 4050 Industriel blvd, Laval, QC, H7L 6C3 450-963-5060 W W W.CANADABILLIARD.COM...