Product Description And Intended Use; Installation; Preliminary Checks For Installation; Product Application Limit - Nice LBar Instructions And Warnings For Installation And Use

12453:2000, points 5.1.1.5 and 5.1.3; in this case installation is compulsory
of at least one pair of photocells as shown in fig. 1.
des: the type tests to check the efficiency of force limitation were performed
with the Force setting at the factory level and Speed setting at the factory val-
ue; with the pole assembled as per the instructions and fitted with the "impact
protection profile" above and below the pole and with the accessory "indicator
lights" XBA4 inserted on the upper impact protection profile.
Special warning to guarantee compliance with the requirement: See
speci fications for the requirement "Safe opening for vertically moving doors".
PRODUCT DESCRIPTION
2
AND INTENDED USE
MBAR and LBAR are electromechanical road barriers for residential and indus-
trial use; they control the opening and closing of a road transit point with widths
from 3 to 8 metres.
Cabinet Pole Rubber
M3BAR 3 m
M5BAR 4 m
5 m
M7BAR 5 m
3+3 m
3+4 m
LBAR 3+4 m
4+4 m
4+5 m
in environmental conditions other than those described in this manual
These barriers are fitted with an electromechanical gearmotor with a 24 V mo-
tor, with incorporated Loop Detector for 2 magnetic loops, with electric limit
switch system and a flashing light signal which can be incorporated in the lid
(optional accessory). These two models may be installed as counterposed bar-
riers in "Master-Slave" mode to cover a surface of a road transit point exceed-
ing 8 metres (see paragraph 7.5).
The control unit is set up for connection to devices belonging to the Nice Op-
era system and to the "Solemyo" solar power system (see paragraph 4.10.3).
The barriers run on electric energy and in the event of a power failure the pole
can be released and moved manually. Alternatively the buffer battery model
PS224 can be used (optional accessory - see paragraph 4.10.2), which guar-
antees a number of automation manoeuvres in the first few hours of power fail-
ure. Should you desire to prolong this period or extend the number of manoeu-
vres, the Stand by function should be enabled (see table 6).
Important points on consulting the manual
- In this manual, the words "road barrier" refer to the two products "MBAR" and
"LBAR".
- The accessories mentioned in the manual are optional.
Available accessory list:
XBA4 - M3BAR and M5BAR pole lights
XBA5 - Aluminium pole painted white, L. 5150 mm
XBA6 - M7BAR pole lights
XBA7 - LED flashing lights that can be installed inside the lid
XBA8 - LED traffic lights that can be installed inside the lid
XBA9 - Universal joint
XBA10 - pivottante connection
XBA11 - Pivot for pole
WA11 - Adjustable pole support (compulsory for LBAR)
WA12 - Mobile support
XBA13 - Impact protection rubber kit
XBA14 - Aluminium pole painted white, L. 4150 mm
XBA15 - Aluminium pole painted white, L. 3150 mm
XBA16 - MBAR foundation plate
XBA17 - LBAR foundation plate
XBA18 - LBAR pole lights
Installable accessories
Lights Rack Mobile
support
(1 piece)
(2 pieces)
(2 pieces)
(3 pieces)
(3 pieces)
3

INSTALLATION

3.1 - Preliminary checks for installation

Before proceeding with installation, check the condition of the product compo-
nents, suitability of the selected model and conditions of the intended installa-
tion environment.
3.2).
all dimensions of the product (fig. 2).
tee a stable fixture.
the barrier raised from the ground.
of manual manoeuvres.
the opening and closing manoeuvres.
ed against the risk of accidental impact.

3.2 - Product application limit

Before installing the product, ensure that all values specified in the chapter
"Technical product specifications" are compatible with the intended use.
– Ensure that the estimated durability (see paragraph 3.2.1) is compatible with
the intended use.
– Ensure that all limits, conditions and warnings in this manual can be ob-
served.

3.2.1 - Product durability

The lifetime is the average economic duration of the product. The value of life-
time is strongly influenced by the intensity of the manoeuvres, i.e. the sum of all
factors that contribute to product wear (see Table 2).
To estimate the lifetime of your automation, proceed as follows:
01. Add the values of the items in Table 2 regarding the system conditions;
02. In Graph 1 from the value obtained above, trace vertical line until it inter-
sects the curve; from this point trace a horizontal line until it intersects the
line of the "manoeuvre cycles". The obtained value is the estimated lifetime
of your product.
The lifetime values specified in the graph are only obtainable if the maintenance
schedule is strictly observed (see chapter "Maintenance schedule"). The esti-
mation of lifetime is made on the basis of design calculations and the results of
tests performed on prototypes. As it is only an estimation, it does not represent
any form of guarantee on the effective lifetime of the product.
Example of calculating the durability of the road barrier (refer to Table 2 and
Graph 1): M5BAR with mobile support (severity index of 10%) - Speed level 3 (se-
verity index of 10%) - Braking (severity index of 10%):
Total severity index = 30%
The estimated durability is approx. 550,000 manoeuvre cycles.
GRAPH 1
1.000.000
800.000
600.000
400.000
200.000
0
Severity index (%)
-
-
-