U-Line Echelon BI-2115 Installation Manual
  1. Manuals
  2. Brands
  3. U-Line Manuals
  4. Ice Maker
  5. Echelon BI-2115
  6. Installation manual
U-Line Echelon BI-2115 Installation Manual

U-Line Echelon BI-2115 Installation Manual

Echelon series
Hide thumbs Also See for Echelon BI-2115:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Service Manual, Use and Care Manual
Installation Guide
BI-2115 — Ice Maker
www.U-LineService.com
Phone (414) 354-0300 • FAX (414) 354-7905
Service & Parts Tech Lines Phone (800) 779-2547 • FAX (414) 354-5696
OnlineService@U-Line.com
©2006 U-Line Corporation
08/2006

Advertisement

Table of Contents
loading

Related Manuals for U-Line Echelon BI-2115

Summary of Contents for U-Line Echelon BI-2115

  • Page 1 Installation Guide BI-2115 — Ice Maker www.U-LineService.com Phone (414) 354-0300 • FAX (414) 354-7905 Service & Parts Tech Lines Phone (800) 779-2547 • FAX (414) 354-5696 OnlineService@U-Line.com ©2006 U-Line Corporation 08/2006...

  • Page 2: Table Of Contents

    Service Information ......17 www.U-LineService.com BI-2115 — Ice Maker 1 Follow Safety Precautions...
  • Page 3 08/2006 BI-2115 — Ice Maker 2 Inspect and Plan You have received a carton containing your BI2115 Ice Maker with a package inside containing a Use and Care Guide, a Product Registration Card and water connection parts.

  • Page 4: Exterior Cleaning

    BI-2115 — Ice Maker 3 Prepare Site Your U-Line product has been designed for either free- standing or built-in installation. When built-in, your unit does not require additional air space for top, sides or rear. However, the front grille must NOT be obstructed and clearance is required for water, drain and electrical connections in the rear.

  • Page 5: Product Dimensions

    90° 90° Door Swing Door Swing Black and White Figure 3 08/2006 BI-2115 — Ice Maker Reversing the Door (Black and White Units Only) All U-Line units (except Handle Stainless Steel models) may be left- or right-hand opening. The door opening is easily reversed by moving the 34-1/8"...

  • Page 6: Other Site Requirements

    For more information see Page 13. Environmental Requirements Many U-Line models are designed to operate in harsh outdoor/marine environments. Special considerations include the following: • The units are designed to operate between 50°F (10°C) and 110°F (40°C).

  • Page 7: Side-By-Side Installation Instructions

    Side-By-Side Installation Instructions For a complete refreshment center, install your BI2115 Ice Maker beside a U-Line Refrigerator, Combo, or Wine Captain Model (see Figure 11 for typical cut-out). Note that each Side-By-Side Installation will be different. • Cut-out width for a side-by-side installation is the total of the widths listed under Cut-Out Dimensions in each unit’s Installation Guide.

  • Page 8: Full Overlay Door Panel

    Full Overlay Door Panel Door Panel Preparation A full overlay door panel completely covers the doorframe and handle to give a built-in appearance. See your U-Line dealer for the optional Full Overlay Door Panel Kit. 2175 Models: P/N U-OL2175B -- Black P/N U-OL2175W -- White 2115 &...
  • Page 9 It is important to ensure that all drilled holes are drilled to the correct depth in order to avoid splits in the wood when hardware is installed. 08/2006 BI-2115 — Ice Maker Installation Instructions Removing Existing Door 1. Remove the door shelves by first pulling shelves up at a 45°...
  • Page 10 Figure 21. The spacers allow the original door panel to slide back into the 1/4"-thick door reveal (channel). www.U-LineService.com BI-2115 — Ice Maker Removed Typical Door Panel Wood Panel...
  • Page 11 4. Replace the door closure assembly onto the bottom pivot post (see Figure 26). Be sure that bosses on closers align with holes in hinge and hinge plate. 08/2006 BI-2115 — Ice Maker Door Closure Top Top Pivot Plate Screw to attach Handle...

  • Page 12: Checking Door Alignment

    2. With door upside-down, loosen but do not remove the two screws on the door’s bottom hinge plate. Figure 28 www.U-LineService.com BI-2115 — Ice Maker Slotted Mounting Holes Raise Outside Door Edge Figure 29 3. See Figure 29. If the top far edge of the door needs to move UP, move the hinge plate toward the outside of the door and retighten screws.

  • Page 13: Water Supply Connection

    (see Figure 33). However, make certain that the tubing is not pinched or damaged during installation. Note: U-Line recommends the use of copper tubing for installation. The use of other types of tubing is not recommended due to potential aftertaste & deterioration over time.

  • Page 14: Electrical Specifications

    • Never use an extension cord to connect power to the unit. Go on to 8 Level the Unit. www.U-LineService.com BI-2115 — Ice Maker 8 Level the Unit Leveling Information It is extremely important that the unit is level. If it is not level, the ice mold will not fill evenly.

  • Page 15: Installation Of The Bi2115

    Solution Make sure that the electrical cord and water supply line are not obstructing the installation. 08/2006 BI-2115 — Ice Maker 10 Start-Up for the First Time Initial Start-Up All Units are shipped with controls that are preset. No initial adjustments are required.

  • Page 16: Start-Up Troubleshooting

    New cubes still appear cloudy. Solution This is normal and is caused by air being trapped in the cube during fast freezing. IMPORTANT See the Use and Care Guide’s Troubleshooting Guide for more solutions. www.U-LineService.com BI-2115 — Ice Maker 08/2006...

  • Page 17: Service Information

    For more than four decades, U-Line has distinguished itself as the leader in built-in undercounter ice making, refrigeration and wine storage appliances. U-Line Corporation, located in Milwaukee, WI, is a family operated manufacturer of built-in ®...

Table of Contents