SPROUT NOMAD ALPHA - Bluetooth Speaker Manual

WHAT'S IN THE BOX?

For optimum performance and safety, please read instructions carefully before usage.

Please keep this manual for future reference.

1x Nomad Alpha Bluetooth Speaker
1x USB-A to USB-C charging cable
1x Aux-in audio cable
1x Product manual

PRODUCT OVERVIEW

1. Power button
2. UNISYNC™
3. LED flashlight button
4. LED indicator
5. Battery LED indicator
6. Wireless charging pad
7. Volume down button
8. Play/pause/answer button
9. Volume up button
10. Locking side panel cap
11. 3.5mm aux input port
12. USB-A output
13. Main power switch
14. USB-C input
15. LED flashlight

QUICK START GUIDE

UNLOCKING THE SIDE PANEL CAP

1. To unlock, turn the cap anti-clockwise
2. Lift the cap to detach

LOCKING THE SIDE PANEL CAP

1. Place the cap over the input panel
2. Turn the cap clockwise until tight*

*Nomad Alpha is only dust and waterproof when this cap is properly closed.

CHARGING YOUR NOMAD ALPHA

1. Switch off the main power switch
2. Connect the speaker via the USB-C input to a power source* using the included USB-A to USB-C cable
3. Blue LEDs indicate the power level of charge**

*Power source options include USB connection to a Sprout AC power adapter, a Sprout car charger or computer/notebook USB connection.

**Full charge will take about 8-10 hours.
Please refer to LED indicator section in this product manual.

CONNECTING VIA 3.5MM AUX CABLE

To play audio using the aux cable, connect the cable from the Nomad Alpha to your device.

Please note: Using 3.5mm aux input will override a Bluetooth source input.

CONNECTING VIA BLUETOOTH

1. Switch on the main power switch
2. Press the power button for approximately three seconds. The LED indicator will flash blue/red to indicate Nomad Alpha is ready for pairing*
3. Turn on Bluetooth on your mobile phone/music device**
4. 'Nomad Alpha' will appear on your mobile phone/ music device. Select 'Nomad Alpha' to pair
5. Once your mobile phone/music device is connected to Nomad Alpha, you will hear 'Bluetooth connected'***
6. Enjoy your music

*If the LED indicator is not flashing red and blue, hold the UNISYNC button for 5 seconds to initiate Bluetooth pairing.

**If you are not familiar with Bluetooth pairing for your mobile phone/music device, refer to the user guide for your mobile phone/music device for instructions to pair a new device using Bluetooth.

***Nomad Alpha will always store the last device paired and if the device is within Bluetooth range, Nomad Alpha will automatically connect to the device.

OPERATING CONTROLS

MAIN POWER SWITCH

The main power switch must be set to the 'ON' position for Nomad Alpha to be operational. The power standby function will only work when the main power switch is in the 'ON' position.

POWER

Press the power button to turn on or off. When turned off, Nomad Alpha remains in standby power mode. Please note that the main power switch at the side panel needs to be switched to on for the power button to operate.

PLAY/PAUSE/ANSWER

Press the play/pause/answer button to play or pause songs and answer mobile phone calls.

VOLUME CONTROL

Short press '-' button to decrease volume.

Short press '+' button to increase volume.

TRACK CONTROL

Long press '-' button to select previous song.

Long press '+' button to select next song.

LED FLASHLIGHT

Hold the LED flashlight button for 5 seconds to turn on or off. Continue pressing the button to cycle through the available flashlight modes. Normal brightness, highlights, slow flash, quick flash.

In about 5% of people with epilepsy, exposure to flashing or flickering lights can trigger seizures (Source: Epilepsy action Australia). The strobe light function in this device may potentially trigger seizures for people with photosensitive epilepsy. User discretion is advised.

CONNECTING MULTIPLE SPEAKERS VIA UNISYNC™

If you are using the UNISYNC feature you can connect one Nomad Alpha as a primary, then connect up to 50 UNISYNC compatible devices as replicas.

To connect a replica, short press the UNISYNC button on your primary device once to enter UNISYNC mode. Once the primary announces it is in UNISYNC mode, repeat on the replica. After the replica announces it is in UNISYNC mode, press the UNISYNC button once more – the replica should now announce it is using UNISYNC audio. The primary speaker will show a solid blue light while replicas will show a flashing red and blue light.

Press the UNISYNC button again to disable UNISYNC.* Press and hold the UNISYNC button for five seconds to reset the UNISYNC function.**

*If UNISYNC is disabled, Nomad Alpha will disconnect from but remember the replicas connected to it.

**Resetting UNISYNC will enable Nomad Alpha to 'forget' all replica devices.

WIRELESS CHARGING

The wireless charging pad conveniently recharge your Qi-compatible devices. The main power switch must be turned on to use this feature.

LED INDICATOR

The single blue LED indicator will flash when Nomad Alpha is switched on

When it is flashing red and blue, Nomad Alpha is in pairing mode.

LED BATTERY INDICATOR

The battery LED indicator will flash from one to four LEDs to indicate Nomad Alpha is charging. The lights will stop flashing once Nomad Alpha is fully charged.

POWERBANK

Nomad Alpha comes with a USB-A output port, which is capable of supplying up to 5V⎓2.4A. The main power switch must be turned on to use this feature.

Whilst charging another device, the LED battery indicator lights will indicate how much charge is remaining in the speaker's powerbank.

SPECIFICATIONS

• Dimensions: 280x 141x 151mm
• Unit weight: 1.9kg
• Output power: RMS 40W
• S/N ratio: 85db +/- 3db
• Frequency range: 90Hz - 20 kHz
• USB-C input: 5V⎓3A (15W), 9V⎓3A (18W), 12V⎓2.5A (30W), 15V⎓2A (30W)
• USB-A output: 5V⎓2.4A (12W)
• Battery capacity: 15,600mAh
• Playtime: Up to 10 hours at 75% volume
• Charging time: Approximately 8-10 hours
• Function: Bluetooth/ UNISYNC/ Aux-in/ Microphone/ USB-C input/ USB-A power output/ LED flashlight/ Wireless charging pad
• Bluetooth version: 5.1
• Drop proof to 2 metres
• Waterproof IP67
• Shock proof
• Operating temperature: -10ºC to 55ºC

CARE AND MAINTENANCE

Nomad Alpha Bluetooth Speaker is intended to be used both indoors and outdoors. The speaker has been tested to IP67 waterproofing and dustproofing standards. IP67 standard allows Nomad Alpha to be submerged in water up to 1 metre for 30 minutes without any damage. However, Nomad Alpha is not intended for constant underwater use. Close the side panel cap properly before use (see locking side panel cap section). If Nomad Alpha is placed in water without the cap securely closed, water will enter Nomad Alpha and void the warranty.

Always make sure the side panel cap is clean, free of any debris and correctly fitted. The speaker will only meet IP67 ratings when the side panel cap is properly locked and sealed. Included USB cables are NOT waterproof.

If you notice a muffling of audio after submersion, gently shake Nomad Alpha to clear excess water. If your speaker is exposed to saltwater clean it thoroughly after use with fresh water. Do not apply excessive force to any surfaces of Nomad Alpha when it is wet or in a wet environment.

Check the rubber seal periodically for premature wear and clean Nomad Alpha with a soft damp cloth and ensure no objects such as dirt, hair, sand are on the rubber seal ring. Do not use any oily solvents or chemicals for cleaning.

IMPORTANT SAFETY INFORMATION

1. Do not attempt to charge Nomad Alpha when it is wet, or you suspect water has seeped into Nomad Alpha. Thoroughly dry Nomad Alpha and make sure all connections are dry before attempting to open the side panel cap and connect to a USB cable or power source. Failure to do so may result in electrical shock, fire or electrical damage to Nomad Alpha and may void the warranty.
2. Do not put metal objects or magnets between the mobile device and the wireless charging surface.
3. Do not use Nomad Alpha near any open fire, heat source or excessive heat.
4. Do not disassemble this device or attempt to modify in any manner. Do not remove the built-in battery or the grill cover. Doing so could cause damage to Nomad Alpha and allow water to enter.
5. Sound levels should be appropriate to your environment and comply with all local regulations. Ensure that you can hear and are aware of any potential hazards around you when you are enjoying your Nomad Alpha.
6. For approximately 5% of people with epilepsy, exposure to flashing or flickering lights can trigger seizures (Source: Epilepsy action Australia). The strobe light function in this device may potentially trigger seizures for people with photosensitive epilepsy. User discretion is advised.

All Sprout products go through thorough quality assurance inspections. If you find that your device is excessively hot, is emitting odour, is deformed, abraded, cut or is experiencing or demonstrating an abnormal phenomenon, immediately stop all product use and contact Sprout.

Sprout Accessories Pty Ltd
W: Sproutinc.com.au | E: enquiries@sproutinc.com.au