Table of Contents
Advertisement
RVD-XG10, RVD-XG10ED, RVA-VK10
6.4.8 Normal command (A thing to move only at the power ON and AJY.)
Command
GPP
Outputs the adjustment value of PICTURE PARAMETER from the RS-232C (Refer to the indication example.)
CNT-dd
Adjust the value of Contrast (-dd=Adjustment value -51 to 0)
BRT±dd
Adjust the value of Brightness (±dd=Adjustment value -25 to +25)
COL±dd
Adjust the value of Color (±dd=Adjustment value -25 to +25)
TNT±dd
Adjust the value of Tint (±dd=Adjustment value -25 to +25)
SHP±dd
Adjust the value of Sharpness (±dd=Adjustment value -25 to +25)
VSa
Switch the video system (a=A:AUTO, P:PAL, S:SECAM, 3:3.58NTSC, 4:4.43NTSC, M:M PAL, N:N PAL)
CLMa
Switch the COLOR MODE adjustment (a=S:STANDARD, V:VIVID)
FRQ+dddd
Fine adjust the value of sample clock frequency (+dddd=Adjustment value +264 to +4104)
PHS+dd
Fine adjust the value of sample clock phase (+dd=Adjustment value 0 to +19)
PSa
Adjust the position of horizontal and vertical directions (a=L, R, U and D)
PPMRST
Clear the PICTURE PARAMETER
GAD
Outputs the adjustment value of mode setting from the RS-232C (Refer to the indication display)
OTa
Select the computer outputs (a=L:LINK, 1:COMP1, 2:COMP2, X:CROSS)
AIa
Adjust the Audio input (a=L:LINK, V:VIDEO, 1:COMP1, 2:COMP2)
BGd
Change the Back Ground color (d=0:Black, 1:Blue)
DSPa
ON/OFF the DISPLAY FUNCTION (INPUT indication, etc.) (a=Y:Indication, N:Non-indication)
RPa
Chenge the screen display direction (a=H:Horizontal, V:Vertical, F:Horizontal and Vertical, N:NORMAL)
LGa
Change the language (a=E:English, D:Deutsch, F:French, I:Italian, S:Spanish, J:Japanese)
Caa
Convergence adjustment (a=R, B, a=L, R, U and D)
LMPRST
The Lamp life meter initialize
TITRST
Total initialize
6.4.9 Factory command (Effective only for adjustments in modes other than Factory)
Command
ROF
Turn OFF the Red panel.
RON
Turn ON the Red panel.
GOF
Turn OFF the Green panel.
GON
Turn ON the Green panel.
BOF
Turn OFF the Blue panel.
BON
Turn ON the Blue panel.
Khh
The control which is the same as the remote control key. It cannot be used simultaneously with the remote control unit.
(hh=The rightmost two digits of the SR code of remote control unit. ex. adjustment + $AA0A→K0A)
KWhh
The control which is the same as the double code of remote control key.
(ex. Jump to integrator mode &AAD3 + $AF23→KW23)
&DLd
Change the H Delay (d=0 to 7)
&CL+ddd
FACTORY OFFSET COLOR adjustment (ddd=0 to 255)
&TN+ddd
FACTORY OFFSET TINT adjustment (ddd=0 to 255)
&SH+dd
FACTORY OFFSET SHARPNESS adjustment (dd=0 to 60)
&Ia+ddd
FACTORY ITO voltage adjustment (a=R, G, B, ddd=0 to 255)
&Ga+ddd
FACTORY GAIN adjustment (a=R, G, B, ddd=0 to 255)
&Ba+ddd
FACTORY BIAS adjustment (a=R, G, B, ddd=0 to 255)
&Ca+ddd
FACTORY SUB CONTRAST adjustment (a=R, G, B, ddd=0 to 255)
&Ha±ddd
FACTORY SUB BRIGHTNESS adjustment (a=R, G, B, ±ddd=-128 to +127)
Note: K and KW can be used in Factory mode.
84
Function
Function
Advertisement
Table of Contents
