Related Manuals for Lumberjack LSM-12DSA
Summary of Contents for Lumberjack LSM-12DSA
- Page 1 SAFETY AND OPERATING MANUAL 12" Heavy Duty Mitre Saw LSM-12DSA ORIGINAL INSTRUCTIONS LSM12DSA...
-
Page 2: Intended Use
Mitre angles of up to 45°. This saw is not designed for cutting firewood. Do not use machines, tools and accessories for anything other than for what they are designed for. SPECIFICATIONS LSM-12DSA Machine Type AC 240V... - Page 3 CUTTING CAPACITY • Mitre table angles: 0 to 50° to the left & 60° to the right • Bevel cuts: 0° to 45° to the left & the right Mitre 0° Mitre left 50° Mitre right 60° Straight Cross Cut Miter Cut at left Miter Cut at right Bevel 0°...
-
Page 4: General Safety Instructions
GENERAL SAFETY INSTRUCTIONS WARNING! Read all safety warnings instructions, illustrations are provided with this power tool. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. 1) Work area safety a) Keep work area clean and well lit. Cluttered and dark areas invite accidents. b) Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. - Page 5 4) Power tool use and care a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. b) Do not use the power tool if the switch does not turn it on and off.
- Page 6 Do not reach behind the fence with either hand closer than 100 mm from either side of the saw blade, to remove wood scraps, or for any other reason while the blade is spinning. Always make certain that there is no gap between the workpiece, fence and table along the line of the cut.
- Page 7 SAW DIAGRAM...
-
Page 8: Installing Or Replacing The Blade
INSTALLING OR REPLACING THE BLADE Make sure that the electrical plug is removed from the power point first, before changing a blade. 1. Loosen but do not remove the three screws on the Guard Plate. 2. Move the Lower Blade Guard downwards. 3. -
Page 9: Adjusting The Mitre Angle
ADJUSTING THE MITRE ANGLE A mitre cut is one that is at an angle across the horizontal surface of the material. A 45° miter cuts to join two pieces in a right-angle corner are common. A 30° cut is often used for a scarf joint or to make a chamfered end. 1. -
Page 10: Using The Depth Stop
3. To use the pre-set detents (stops), push the Bevel Detent Lever back until the Saw Head Assembly can be moved and then release the Lever. The Saw Head Assembly will lock into place at often used bevel angles, including 22.5°,33.9°, and 45°... -
Page 11: General Operation
WORKPIECE & WORK AREA SET UP 1. Designate a work area that is clean and well lit. The work area must not allow access to children or pets in order to prevent distraction and injury. 2. Direct the power cord along a safe route to reach the work area without creating a tripping hazard or exposing the power cord to possible damage. -
Page 12: Before Operation
Do not bear down on the material—use light downward and lateral pressure. If the material binds to the blade, release the Trigger. 8. When the cut is completed, raise the Saw Head, release the Trigger, and wait for the Blade to stop turning, release the Clamp and remove the workpiece from the Saw. -
Page 13: Maintenance And Inspection
MAINTENANCE & INSPECTION CAUTION! Confirm that the switch is disconnected and unplug the power plug from the power socket to avoid serious accidents. 1. Calibrating a. Calibrating the Mitre Scale To make accurate cuts, the Saw Blade must be perpendicular (at a 90º angle) to the Fence. To adjust the setting: 1. -
Page 14: Parts List
PARTS LIST Item No. Part Quantity Item No. Part Quantity Left Base Handle Washer Bevel Clamp Foot Base Bevel Shaft Bevel Lock Handle M8 Screw Right Base Handle Left Bevel Indicator Washer Miter Scale Table Pad Waveform Washer M16 Nut Miter Lock Knob Bevel Detent Plate Detent Shaft Driving Assembly... - Page 15 PARTS LIST Middle Gear Stator Gear C-Ring Armature 6000 Bearing Magnet Ring Connection Gear Cord Clip Rubber Column Motor Housing Trigger Gear Holder M5 jam nut Bottom Handle Screw Ring Washer 6002 Bearing Switch Spindle Fan Cover Cover M6x80 Screw Inner Flange Top Handle Blade...
-
Page 16: Assembly Diagram
ASSEMBLY DIAGRAM... - Page 17 DECLARATION OF CONFORMITY We Importer: TOOLSA VE LTD Unit C, Manders Ind. Est., Old Heat h Road, Wolverhampton, WV1 2RP. Declare that the product: Designation: 12" PROFESSIONAL MITRE SAW Model: SM-12DSA Complies with the following Directives: Electromagnetic Compatibility Directive Restrictions of the use of Hazardous Substances in Electrical Equipment Waste Electrical and Electronic Equipment Standards &...
Need help?
Do you have a question about the LSM-12DSA and is the answer not in the manual?
Questions and answers